The Unit for the Kinematic Study of Gear Trains, "KSGT", unit includes a pivoting rail with a fixed axle to which two more axles can be fixed in any position in function of the feature to study.The cogwheels may be assembled on the axles in...

The Unit for the Study of Porous Beds in Venturi Tubes (Darcy´s Equation), "FME24", designed by EDIBON, for the study of porous beds in Venturi tubes (Darcy's Equation), allowing the complete and detailed understanding of this equation.The unit is...

It is a control gear. Its function is to control the space between teeth.

It is a mitre gear. It is made up of bevel gears that consist of two conical cogwheels. This device is used to transmit motion between two perpendicular shafts.

It is a multiple-disk clutch. Multiple-disk clutches allow for transmitting higher torques. Such clutches are used in the steering of chain tractors.

It is a planetary gear. It consists of one or more external or planet gears that revolves about a central or sun gear. Planetary gears are normally used as reducers in gearboxes or as differentials.

The Unit to Study a Shaft with Journal Bearings Assembly, "SJBA", unit consists of two shaft bearings at the ends and a ground steel shaft. The slide bearing consists of two parts, the bearing itself, which is the part of the assembly that is in...

It is a spur gear. This type of gear is the simplest one, normally used for low or medium speeds, since they are noisy if not well-formed.

It is a two-stage spur gear. Two-stage gears are used when rotation transmission between shafts cannot be obtained with only one pair of gears.

It is a variable speed belt drive. Continuously variable gearboxes are the ideal transmission since they change the speed ratio continuously. For that reason they are considered an automatic transmission with infinite number of ratios. Variable...

It is a worm gear with shafts perpendicular to each other. It consists of a helical worm screw and a circular cogwheel. Some applications of this device are automatic doors or elevators systems, where motion in one direction and blocking the...

The Unit to Study Rotational Inertia, "SRI", has been designed to carry out tests to analyze the moments of inertia of a solid and a hollow cylinder, both with same mass and diameter. The moment of inertia of another hollow cylinder with different...

The Unit to Study the Pressure Drop of Compressible Fluids in Pipes, "PDCFP", allows the study of the compressible fluid pressure drop, for example the air of a compressor, and the different flow conditions (laminar and turbulent) thanks to the...

The Universal Buckling Unit "MUP" is a bench-top unit whose frame is made of anodized aluminum profiles and plates and steel elements, on which a bubble level is installed to equilibrate the system.The unit has been designed to carry out tests...

The Universal Material Testing Unit, "EEU/20KN", is a didactic bench-top universal material testing unit. It is distinguished by its rigid construction, accurate control and a precise hydraulic system to apply loads of up to 20 kN, which enables...

The Unsteady State Heat Transfer Module for TSTCB, "TXC/EIB", bench-top unit has been designedto allow practices and exercises to be performed in unsteady state heat transfer. It studies transient conduction with convection. Using different shapes...

TXC/EI. Unsteady State Heat Transfer Module for TSTCC: study of heat transfer in the non-stationary state Study of transient conduction with convection.Bench-top unit designed to allow practices and exercises to be performed in unsteady state heat...

The system consists of a vertical cantilever rigidly clamped at its lower end to the main column which is attached to a rigid structure. Beams of different sections may be used.A loading head, located at the upper end of the column, can rotate...

The Venturi, Bernoulli and Cavitation unit, "FME22", has been designed by EDIBON to demonstrate some of the practical possibilities that can be achieved with a Venturi tube.This unit is designed for demonstrating some practical possibilities with...

The Vibration of Coil Spring Unit, "MVRE", unit has been designed to study and understand a coil torsion spring, a mass-spring system and the fundamental properties of its characteristic periodic motion. In this sense, the unit consists of a rigid...

Vibrations and/or Deformations Test Module, "BS1" has been designed to teach mechanical vibration and displacement variable measurement techniques.On the upper side of the test module there is a girder or elastic/vibrant sheet that is the one...

The Voltage Transformer Fundaments Application for Protection Devices, "AEL-VTFP", has been designed by EDIBON to show the students which the main functions of voltage transformers are and which the parameters that must be considered in order to...

The "RYC-TAG" Water Flow Temperature Control module has been designed to study a practical control system, through the control of water flow temperature.The "RYC-TAG" module consists of two main components: the "RYC-TAG" apparatus and the...

With the Water Hammer unit, "FME15", designed by EDIBON, we can demonstrate the effects of the instantaneous or gradual variation of the velocity of a fluid.The water hammer phenomenon, which appears as a consequence of a rapid change in the...

The Wheel and Differential Axle Unit, "MRYE2", is a unit that allows for investigating the mechanics of a wheel and differential axle mechanism and demonstrating the force reduction on a differential pulley block.A wheel, consisting of a pulley...

The Whirling of Shafts Unit, "MEER", has been designed by EDIBON to demonstrate and determine different modes of oscillation and resonance of shafts with continuous distribution of mass under different conditions.The operation of the Whirling of...

The Whitworth Quick Return Mechanism, "MBM2", is a mechanism able to transform circular movement into reciprocating movement. It ismade of aluminum and consists of a rotary element, called crank, with a graduated disk, connected to a rigid bar,...

The Wind Energy Basic Unit, "MINI-EEE", is a small-scale unit designed to study wind energy and the influence of some factors on its generation.This unit consists of a transparent tunnel, a wind turbine with rotor to place up to six blades and a...

The purpose of this application is the study of wind power plants in the context of microgrids. It consists of an induction turbine-generator group whose purpose is to provide energy to the micro grid by making an intelligent energy distribution...

The Wind Energy Unit, "EEE", contains an aerogenerator, in laboratory-scale, and is used to study the conversion of kinetic wind energy into electrical energy and to study the influence of some factors on this generation.The unit consists of a...