It is an electrically heated steam generator (3 kW electric resistance). The resistor has an internal thermostat at 150ºC.This type of generator produces steam for an operating pressure of 0.9 bar, with a maximum pressure of 2 bar.The maximum...

A steam generator is an assembly or system formed by its boiler and its accessories, designed to transform a liquid into steam, at temperature and pressure different from that of the atmosphere. Its function is to produce steam to be used in...

It is an electrical heating horizontal steam generator (with two heating elements of 6 kW each). It consists of a horizontal cylindrical body with torispherical ends joined by arc welding. This type of generator produces 12 Kg.v.h of steam for...

The "N-EM" are a series of emulators that provide the students the required hardware to emulate the most common automatic systems.The "N-EM" modules are designed to work with the "AE-PLC" units to obtain the fundamental knowledge of PLC...

The Stirling Motor, "TMSB", is used to demonstrate the operation of a thermodynamic machine for the conversion of energy. It converts thermal energy into mechanical energy and operates as a motor (heat engine). Additionally it can operate an...

The Strain Gauge Training Unit, "MEGE", provides an introduction to the fundamentals of measurement with strain gauges, to compare how resistance strain gauges work and how they measure strains in different structures (torsion, tension and bending...

The Stress Hypotheses Unit, "STH", allows the study and testing of stress hypotheses by applying loads in different directions on a test specimen point and measuring the deformations produced.Normal and shear stresses are applied, avoiding...

The Strut Buckling Unit "MFLT" allows the student to obtain experimentally the buckling critical load of slender struts subjected to compression.The unit allows to study the buckling of pieces of different lengths, ranging from 300 mm. to 625 mm.,...

The Suspension Bridge Unit, "MVS", consists of a deck and two parallel main cables that simulate a suspension bridge and allow the study of stress in the main cables. The deck of the bridge is simulated by a light alloy beam that is held by both...

The Switching in Transmission and Distribution Substations Application, "AEL-SST-01", has been developed by EDIBON to study the most common operations carried out in these substations, such as, transference of the electrical service from the first...

The Tachometer Test Module, "BS7", has been designed to teach linear and angular speed measurement techniques. In this module placed on the upper part we have a miniature motor used to move the axle. The motor speed can be changed adjusting the...

The Teaching Cream Separator, "DSN", allows the study of the separation of a dense phase liquid from a lighter phase liquid, in particular the separation of the cream from the milk in a disk stack centrifuge.The system is mounted on a table base...

CODITEL is a digital circuit commutation unit for didactic purposes. Its structure is like a temporal commutator structure with two MIC ways, one inlet way and one outlet way. Basically, it follows the recommendation of the CCITT and of...

The "RYC-TE" Temperature Control module has been designed to study a practical control system, through the control of the water temperature in a tank.The "RYC-TE" module consists of two main components: the "RYC-TE" apparatus and the "RYC-TE"...

The Temperature Measurement Training Unit, "TEMT", allows to compare the response of several devices to measure the temperature for different flows and different installation position of these devices.The unit includes four different measuring...

The Temperature Measurement Unit, "TMT", works as a temperature meter that uses different temperatures measuring devices to compare, check and analyze the temperature and how is the precision for the measure and for the device that the student has...

The Temperature Test Module, "BS2", has been designed to teach the use and applications of sensors of temperature as a measure, and its control.We have a half-open space in whose interior there are two lamps that are going to heat that space....

With the Tensile Tester Unit, "MTTU", tensile test can be performed. A specimen made of different materials is subjected to an increasing axial tensile stress till failure. This unit allows the user to perform tensile tests with different...

TXC/LG. Thermal Conductivity of Liquids and Gases Module for TSTCC: study of the thermal conductivity of any gas or liquid compatible with building materials.This unit has been designed to enable students to easily determine the thermal...

The Biomedical Microwave Thermal Effects Teaching Unit, "BIMTE", allows the students to test microwave therapy, so as to achieve a better knowledge on its functioning and internal mechanism.The Biomedical Microwave Thermal Effects Teaching Unit,...

This unit is a system that transforms solar energy into usable thermal energy.This unit uses the thermosiphon system to heat water or the traditional pumping system. In both cases, the absorbed thermal energy is given by the simulated solar...

The Thermal Solar Energy Unit, "EEST", is a system that transforms solar energy into usable thermal energy. It uses the thermosiphon solar system to heat water or the traditional pumping system. In both cases, the absorbed thermal energy is given...

In the Thick-Walled Cylinder Unit, "MCPG", the stresses are determined through the measurement of the strains produced on the surface. These strains are measured by strain gauges.The thick-walled vessel consists of an aluminum cylinder of length...

TXC/TE. Three Axes Heat Transfer Module for TSTCC: study of heat transfer by studying the direction in the three axes.Bench-top unit designed to carry out heat transfer experiments and exercises studying the direction in three axes.

The Three-Hinged Arch Unit "MART" allows the student to become familiar with three-hinged arches, to calculate the bearing forces (for point load, for uniformly distributed load and for moving load), to investigate the influence of the load on the...

Three-phase voltage is essentially a system of three alternating voltages, coupled (all 3 are produced simultaneously in a generator) and 120º out of phase with each other (i.e. one third of the period).The Three-phase Circuits Module, "N-M18",...

The Three-phase Installations Faults Application, "AEL-AD33T", has been designed to study several protections belonging to industrial installations. Through safety elements, the students can simulate different faults and verify the reasons why...

The Three-Phase Transformer Application, "AEL-TPTT", has been designed by EDIBON to allow the students learn how to carry out different three-phase transformer tests and how they work.With this application the user will study the basic operating...

The Torsion and Bend Unit, "MTP", is a combined apparatus for the demonstration of both torsion and bend to be used in the laboratory or as a complement of the theoretical study about torsion and bend. Its size and weight facilitate its transport...

To perform the tests, the test specimen is clamped and twisted by means of a flywheel and a worm gear until it breaks. The force is gradually applied to the specimen to observe the elastic strain produced. The specimen will deform and manifest...

The Torsion Unit, "MTB", allows to verify the basis of torsion and to perform practical exercises to demonstrate:Circular rods elastic torsion equation.The rigidity modulus of different materials.To perform the tests a metallic rod is fastened by...

The Torsional Oscillations Unit, "MOT", is intended for easy experiments. It enables to illustrate and investigate the torsional oscillation in single rotor, multi-rotor and geared systems. The unit basically consists of a rigid frame that have...

The "N-EM" are a series of emulators that provide the students the required hardware to emulate the most common automatic systems.The "N-EM" modules are designed to work with the "AE-PLC" units to obtain the fundamental knowledge of PLC...

The Transmission Lines Unit, "ELT", has been designed by EDIBON to study a standardized coaxial line to analyze realistic measurements.The Transmission Lines Unit "ELT" has been designed as integrated unit for help the student to understand the...