9.10.- INSTALLATIONS ET MAINTENANCE

The needs of today's society are a challenge for any industry, since they have to be in continuous evolution and renewal to adapt to those needs.

Voir plus

In recent years, as a result of the new industrial revolution or ",Industry 4.0, the emergence of the ",Industrial Internet of Things (IIoT) and the Smart Factories",, that adaptation is possible thanks to the application of the most sophisticated techniques in the design of new facilities or in the renovation of existing ones.

In the energy industry field, in addition to the demand for new services, the compliance with the energy efficiency regulations, which are increasingly demanding, is also important. This continuous demand for requirements produces a need for constant research of new systems and elements to optimize the facilities.

With all these technological advances and the exhaustive controls carried out, it should not be forgotten that any element that takes part in the process is going to be subjected to a mechanical wear (corrosion, wear, thermal expansion, etc.) and its useful life is limited. To avoid catastrophic failures, stoppages in production or any type of process that implies an increase of non-productive times and, therefore, an increase of costs, it is extremely important to carry out a good maintenance of machinery.

Traditionally, only two types of maintenance were considered:

    • Corrective: the fault is solved once it has already occurred.
    • Preventive: periodic review of all those problematic elements and their replacement if required.

Nowadays, thanks to the available technology, it is possible to carry out predictive maintenance consisting of a comprehensive analysis of all those variables that take part in all the components of a system and be able to replace them at the right time. This means an important saving of maintenance costs.

But, if more control over the failures that can suffer all those mechanical components subject to wear is preferred, there is another type of maintenance, known as proactive maintenance. It goes one step further than the predictive maintenance, looking for the root of the problem. In the field of thermal installations, there are installation simulation programs that detect incidents or schedule checks when required.

Voir les produits
PRODUITS DE INSTALLATIONS ET MAINTENANCE
Affichage 1-30 de 33 article(s)
UNIT TO STUDY A FILTER DRIER  CUTAWAY MODEL - DFCM
  • DFCM
Available
9.10.1.- MODÈLES EN COUPE
DFCM

Unit to Study a Filter Drier Cutaway Model

The Unit to Study a Filter Drier Cutaway Model, “DFCM”, allows the students to visualize the inner parts of a (element), to evaluate the relation with each other accurately and to understand their functionThe cutaway model of a filter drier is...
UNIT TO STUDY A GAS METER CUTAWAY MODEL - GMCM
  • GMCM
Available
9.10.1.- MODÈLES EN COUPE
GMCM

Unit to Study a Gas Meter Cutaway Model

The Unit to Study a Gas Meter Cutaway Model, “GMCM”, allows the students to visualize the inner parts of a gas meter, to evaluate the relation with each other accurately and to understand their function.It is a measurement device to determine the...
UNIT TO STUDY A HELICAL OIL SEPARATOR CUTAWAY MODEL - HOSCM
  • HOSCM
Available
9.10.1.- MODÈLES EN COUPE
HOSCM

Unit to Study a Helical Oil Separator Cutaway Model

The Unit to Study a Helical Oil Separator Cutaway Model, “HOSCM”, allows the students to visualize the inner parts of a liquid separator, to evaluate the relation with each other accurately and to understand their function.It is a real model used...
UNIT TO STUDY A LIQUID SEPARATOR CUTAWAY MODEL - LSCM
  • LSCM
Available
9.10.1.- MODÈLES EN COUPE
LSCM

Unit to Study a Liquid Separator Cutaway Model

The Unit to Study a Liquid Separator Cutaway Model, “LSCM”, allows the students to visualize the inner parts of a liquid separator, to evaluate the relation with each other accurately and to understand their function.The cutaway model of a liquid...
INTRODUCTION TO REFRIGERATION UNIT - TIR
  • TIR
Available
9.10.3.- INSTALLATIONS ET MAINTENANCE
TIR

Équipement d'Introduction de Réfrigération

The Introduction to Refrigeration Unit, “TIR”, is a system with exchangeable modules in which the components are mounted on plates and are rapidly connected by flexible hoses. The unit consists of a frame where 6 of the 8 modules are positioned at...
TEMPERATURE MEASUREMENT TRAINING UNIT - TEMT
  • TEMT
Available
9.10.3.- INSTALLATIONS ET MAINTENANCE
TEMT

Équipement de Formation pour Mesures de Température

The Temperature Measurement Training Unit, “TEMT”, allows to compare the response of several devices to measure the temperature for different flows and different installation position of these devices.The unit includes four different measuring...
RADIATORS TRAINING UNIT - RT
  • RT
Available
9.10.3.- INSTALLATIONS ET MAINTENANCE
RT

Radiators Training Unit

The Radiators Training Unit, "RT", has been designed to study hot water heating systems. These systems are called that way because theyuse water as working fluid between the generation system, usually a boiler, and the emitters, such as radiators,...
HEATING SYSTEM TRAINING UNIT - THST
  • THST
Available
9.10.3.- INSTALLATIONS ET MAINTENANCE
THST

Équipement de Formation de Chauffage

The Heating System Training Unit, "THST", has been designed to study central heating systems. The unit simulates a central heating system. For that purpose, it is made up of four radiators with a thermostatic valve each. This valve controls the...
THREE-WAY MIXING VALVE TRAINING UNIT - TEV3V
  • TEV3V
Available
9.10.3.- INSTALLATIONS ET MAINTENANCE
TEV3V

Équipement de Formation de Valvule Mélangeuse de 3 Voies

The Three-Way Mixing Valve Training Unit, "TEV3V", allows to demonstrate the function of a three-way mixing valve in a hot water heating system. The three-way mixing valve in the heating system regulates the supply water temperature to a heating...
FOUR-WAY MIXING VALVE TRAINING UNIT - TEV4V
  • TEV4V
Available
9.10.3.- INSTALLATIONS ET MAINTENANCE
TEV4V

Équipement de Formation de Valvule Mélangeuse de 4 Voies

The Four-Way Mixing Valve Training Unit, "TEV4V", allows to demonstrate the function of a four-way mixing valve in a hot water heating system. The four-way mixing valve in the heating system regulates the circulation and feed flow temperatures of...
SANITARY FITTINGS TRAINING UNIT - TEIS
  • TEIS
Available
9.10.3.- INSTALLATIONS ET MAINTENANCE
TEIS

Équipement de Formation de Raccords Sanitaires

The Sanitary Fittings Training Unit, "TEIS", has been designed by EDIBON for training in the plumbing sector. It consists of an anodized aluminum frame and panels in painted steel in which tests can be carried out with the most common systems of...
DRINKING WATER INSTALLATION UNIT - TIAP
  • TIAP
Available
9.10.3.- INSTALLATIONS ET MAINTENANCE
TIAP

Équipement d'Installation d'Eau Potable

The Drinking Water Installation Unit, "TIAP", has been designed to demonstrate domestic water heating from the cold water supply. A typical domestic drinking water system is attached to the front panel of the unit. The unit includes the most...
PROTECTION OF DRINKING WATER TRAINING UNIT - TPAP
  • TPAP
Available
9.10.3.- INSTALLATIONS ET MAINTENANCE
TPAP

Équipement de Protection en Installations d'Eau Potable

The Protection of Drinking Water Training Unit, “TPAP”, has been designed by EDIBON to study cases in which the drinking water system is contaminated with wastewater. It is specially designed for the training of students in the plumbing sector.The...
PIPE CLEANING TRAINING UNIT - TELT
  • TELT
Available
9.10.3.- INSTALLATIONS ET MAINTENANCE
TELT

Équipement d'Étude de Systèmes de Nettoyage de Tubes

The Pipe Cleaning Training Unit, “TELT”, designed by EDIBON, simulates a real house piping system, so original components used in plumbing systems are employed. The objective of this unit is to study the cleaning of pipes from the sanitation...
SEWERAGE UNIT - TSID
  • TSID
Available
9.10.3.- INSTALLATIONS ET MAINTENANCE
TSID

Équipement de Système d'Évacuation

With the Sewerage Unit, "TSID", tests about a wastewater sanitation system can be made and the flow in a sewage system can be observed.Its design allows the study of the operation and performance of sewage systems. It is specially designed for...