MODULES D'ALIMENTATION

Additional supplies in a laboratory or industry are defined as those supplies necessary for a proper operation of the units. The most common additional supplies are the supply of hot and cold, electricity, process and cooling water, steam and compressed air.

Voir plus

Each of these supplies is vital depending on the activity to be performed, e.g. the electrical supply to drive a motor or operate a resistor, the hot or cold supply to control the temperature or the compressed air to control pneumatic valves.

The necessary process heating can be supplied from a steam or a heat-bearing fluid (water or oil) and is produced by electrical equipment (resistors) or boilers in which a fuel is burned. Cooling is generated by a refrigeration cycle using the heat absorbed in the refrigerant evaporation process. And, compressed air can be supplied from cylinders where gases are stored at a very high pressure or by using compressors.

The scientific area of laboratory equipment would be inconceivable without these additional supplies necessary to carry out the laboratory activities in an appropriate manner.

Voir les produits
PRODUITS DE MODULES D'ALIMENTATION
Affichage 1-15 de 15 article(s)
STEAM GENERATOR (3 KW) - TGV
  • TGV
Available
MODULES D'ALIMENTATION
TGV

Générateur de Vapeur (3 kW)

It is an electrically heated steam generator (3 kW electric resistance). The resistor has an internal thermostat at 150ºC.This type of generator produces steam for an operating pressure of 0.9 bar, with a maximum pressure of 2 bar.The maximum...
STEAM GENERATOR (6 KW) - TGV/6KW
  • TGV/6KW
Available
MODULES D'ALIMENTATION
TGV/6KW

Générateur de Vapeur (6 Kw)

A steam generator is an assembly or system formed by its boiler and its accessories, designed to transform a liquid into steam, at temperature and pressure different from that of the atmosphere. Its function is to produce steam to be used in...
WATER HEATER MODULE - WHM
  • WHM
Available
MODULES D'ALIMENTATION
WHM

Module de Chauffe-Eau

The Water Heater Module, "WHM", designed by EDIBON is an efficient device for rapid and precise fluid heating. The water heater module can be used as a complement to other units for water heating. The unit can be used to heat the fluid to the...
REFRIGERATION OR HEATING WATER RECIRCULATION UNIT - TERA
  • TERA
Available
MODULES D'ALIMENTATION
TERA

Unité de Recirculation de l'Eau de Réfrigération

The Refrigeration Water Recirculation Unit, "TERA", is a reversible heat pump that allows the heating and cooling of a volume of water.It is a recirculation heat pump designed to provide a continuous supply of water cooled or heated at the...
MAINTENANCE KIT CONTAINING LEAKAGE DETECTOR - T/KIT2
  • T/KIT2
Available
MODULES D'ALIMENTATION
T/KIT2

Kit de Maintenance contenant un Détecteur de Fuites

The Maintenance Kit containing Leakage Detector, "T/KIT2", includes a portable detector sensitive to concentrations of all commercial refrigerants with the objective of locating leaks in refrigeration systems. Refrigerants detectable by the kit...
SILENT AIR COMPRESSOR UNIT - SAC
  • SAC
Available
6.1.3.2.- PNEUMATIQUE
SAC

Unité de Compresseur d'Air Silencieux

L’Équipement de Compresseur d’Air Silencieux, "SAC", a été conçu par EDIBON pour fournir de l’air comprimé à l’équipement de EDIBONqui comprend des circuits pneumatiques.L’équipement SAC contient les composants permettant de filtrer et de réguler...
HYDRAULIC POWER UNIT - HPU
  • HPU
Available
6.1.3.1.- HYDRAULIQUE
HPU

Unité de Pompe Hydraulique

L’Équipement de Pompe Hydraulique, "HPU", conçu par EDIBON fournit tous les composants nécessaires pour alimenter en huile de travailsous pression les équipements EDIBON comprenant des circuits hydrauliques.L'équipement HPU dispose des composants...
HYDRAULICS BENCH - FME00
Available
8.1.1.- UNITÉS DE BASE
FME00

Banc Hydraulique

Accessoire de LIFLUBA
Unit for the study of fluid behaviour, hydraulic theory and the properties of fluid mechanics. It is formed by a movable hydraulics bench used to hold a wide variety of modules, which allow the student to experiment with the problems presented by...
BASIC HYDRAULIC FEED SYSTEM - FME00/B
Available
8.1.1.- UNITÉS DE BASE
FME00/B

Source d'Alimentation Hydraulique de Base

Accessoire de LIFLUBA
The Basic Hydraulic Feed System, "FME00/B", designed by EDIBON is a service unit for different Fluid Mechanics Units as: "FME" type modules, Fluid Friction in Pipes Unit "AFT", etc., increasing the equipment profitability.
AUXILIARY TRANSFORMER AND PROTECTION UNITS - AUTP
  • AUTP
Available
LES TRANSFORMATEURS AUXILIAIRES ET DE PROTECTION
AUTP

Unités Auxiliaires et Transformateurs de Protection

The Auxiliary Transformer and Protection Units, "AUTP", are a range of auxiliary single phase and three phase transformers used to adapt the voltage level of any country in the appropriate voltage for EDIBON units. They have an input voltage range...
Demander des informations