The Computer Controlled Supersonic Wind Tunnel (Three Blowers), "TAS25/100C-3B", is an open wind tunnel for the study of theaerodynamic properties of different drag bodies subject to subsonic and supersonic flows. Airflows through three vacuum...

The Computer Controlled Teaching Autonomous Pasteurization Unit "PADC" receives cold milk from a refrigeration tank (not included). The milk is impelled with a milk pump (computer controlled). It is heated in the heat exchanger, by counter-current...

The Computer Controlled Teaching Cheese Press, "PVQC", consist of a pneumatic press to compress the fresh curd in order to remove excess of whey, since spoilage of the cheese is hastened by retention of too much water in the finished cheese. This...

The Computer Controlled Teaching Cream Separator, "DSNC", allows the study of the separation of a dense phase liquid from a lighter phase liquid, in particular the separation of the cream from the milk in a disk stack centrifuge. The system is...

The Computer Controlled Teaching Curdling Tank, "CCDC", is employed to curdle milk, which is an essential process to make cheese.The unit has tank, water jacket, coil with one inlet and outlet for the water of the boiler, inlet for the water of...

The Teaching Unit for the Study of Digital Signal Processing "TDS" allows to study the principles and more important concepts about digital signal processing, including study and practical exercises, among others, of:Continuous waveforms...

The Computer Controlled Teaching Unit for the Study of Power Electronics (with IGBTS), "TECNEL" is a unit with Computer Control and Data Acquisition System designed to study the basis of Power Electronics. It allows students to study AC/DC, DC/AC,...

Regulation and control theory is divided into two major divisions in, namely, classical and modern. The implementation of classical controller designs as compared to systems designed using modern control theory is easier and these controllers are...

The Computer Controlled Teaching Yogurt Incubator, "IYDC", is called yogurt maker or yogurt heater. This yogurt maker consists of an insulated central body where yogurt fermentation is carried out.There is a series of shelves inside to place the...

The Computer Controlled Temperature Measurement Unit, "TMTC", works as a temperature meter that uses different temperatures measuring devices to compare, check and analyze the temperature and how is the precision for the measure and for the device...

The Computer Controlled Test Bench for Single-Cylinder and Two-Cylinders Engines, 11 kW, "TBMC12", designed by EDIBON, is a teaching unit to test internal combustion engines of up to 11 kW.The element of the unit that offers load torque is an eddy...

The Computer Controlled Test Bench for Single-Cylinder Engines, 2.2 kW, "TBMC3", designed by EDIBON, is a teaching unit to test internal combustion engines of up to 2.2 kW.The unit has an element to exert the braking torque, an asynchronous motor...

The Computer Controlled Test Bench for Single-Cylinder Engines, 7.5 kW, "TBMC8", designed by EDIBON, is a teaching unit to test internal combustion engines of up to 7.5 kW.The element of the unit that offers load torque is an eddy current...

The Computer Controlled Test Bench for Four Cylinders Engines, 75 kW, "TBMC75", designed by EDIBON, is a teaching unit to test internal combustion engines of up to 75 kW.The element of the unit that offers load torque is an eddy current...

The Computer Controlled Test Bench for Hybrid Engine, "TMHC", is a teaching unit that allows to study and analyze the power source of a hybrid vehicle, consisting on a combination of an electrical motor and an internal combustion engine.These two...

The Computer Controlled Thermal Conductivity of Building and Insulating Materials Unit, "TCMC", is a unit employed to measure thermal conductivity of low-conductivity materials, such as insulating materials.This unit is a calibrated instrument...

The Computer Controlled Thermal Conductivity of Liquids and Gases Unit, "TCLGC", has been designed by EDIBON to allow the students to appreciate and understand the heat transfer process through any gas or liquid locked in a solid.By the...

The Computer Controlled Thermal Radiation and Light Radiation Unit, "TRTC", has been designed to demonstrate the laws of radiant heat transfer and radiant heat exchange. It basically consists in two independent parts. One of the parts is for the...

The Computer Controlled Thermal Solar Energy Basic Unit, "MINI-EESTC", allows to demonstrate solar thermal heating of domestic water in an illustrative manner.This unit is a system that transforms solar energy into usable thermal energy. It uses...

The Computer Controlled Thermal Solar Energy Unit, "EESTC", is a system that transforms solar energy into usable thermal energy. It uses the thermosiphon solar system to heat water or the traditional pumping system. In both cases, the absorbed...

The Computer Controlled Thin Film Evaporator "EPFC" has been designed to study (theoretical and practically) the different operating variables that influence the thin film evaporation process.The unit is formed by a thin film evaporator, a...

The Computer Controlled Three Dimensional (3D) Physics, "EFAC", from EDIBON, allows to do practical exercises in the different fields of physics (electricity, magnetic fields, mechanics, acoustics, optics and thermodynamics).The "EFAC" is an open...

Tidal energy is another way to generate electricity extracting energy from the sea. Twice a day big volumes of water rise and fall with the tides.A Tidal Barrage make use of the potential energy in the difference in height (or head) between high...

The Computer Controlled Torsional Vibration Unit, "MEVTC" is designed to study torsion suffered by some shafts with rotation motion, apart from studying the torsional rigidity and the behavior of a torsional vibration system with one, two or three...

The Computer Controlled Tray Drier "SBANC" is a laboratory scale unit designed to study fluid mechanics, surface chemistry, solids structures and mass and energy balances related to the drying process.It consists of a tunnel, several trays where...

The Computer Controlled Tubular Flow Reactor for QRC, "QRTC", has been designed by EDIBON to conduct the kinetic study of homogeneous liquid-liquid reactions. In this unit, a continuous stream of reactants is passed through, which mix and react as...

The main element of the Computer Controlled Two-Shaft Gas Turbine "TGDEC" is the High Pressure Turbine, which is also called Gas Generative Turbine. It consists of:Radial compressor, which is feeded by atmospheric air to compress it.Tubular...

The main element of the Computer Controlled Two-Shaft Gas Turbine/ Jet Engine, "TGDEPC", is the High Pressure Turbine, which is also called Gas Generative Turbine. It consists of:Radial compressor, which is feeded by atmospheric air to compress...

The Computer Controlled Two-Stage Compression Refrigeration Unit, "TSCC", is clearly organized and represents a two-stage compression refrigeration system to obtain low temperatures.The main components of the unit are:Two hermetic compressors in...

The Computer Controlled Two-Stage Compressor Test Unit, "HCDEC", works with compressed air and presents as a principal device a compression bench with two pistons, low and high pressure.This unit presents four circuits or work dispositions which...