Best sales

Best sellers

Showing 889-912 of 927 item(s)

UNIT TO STUDY A MULTIPLE-DISC CLUTCH CUTAWAY MODEL - DCCM

Accessory of CMTM

Available

7.4.1.- CUTAWAY MODELS

DCCM

Unit to Study a Multiple-Disc Clutch Cutaway Model

Accessory of CMTM

The Unit to Study a Multiple-Disc Clutch Cutaway Model provides insight into the operation of this clutch system, which uses multiple friction discs to increase torque transmission capacity.This type of clutch is widely used in chain tractor...

UNIT TO STUDY A PLANETARY GEAR CUTAWAY MODEL - PGCM

Accessory of CMTM

Available

7.4.1.- CUTAWAY MODELS

PGCM

Unit to Study a Planetary Gear Cutaway Model

Accessory of CMTM

The Unit to Study a Planetary Gear Cutaway Model provides an in-depth analysis of this type of transmission, which consists of one or more external (planet) gears rotating around a central (sun) gear.Planetary gears are widely used in vehicle...

UNIT TO STUDY A SHAFT WITH JOURNAL BEARINGS ASSEMBLY - SJBA

SJBA

Available

7.4.2.- DETACHABLE MODELS

SJBA

Unit to Study a Shaft with Journal Bearings Assembly

The Unit to Study a Shaft with Journal Bearings Assembly, "SJBA", unit consists of two shaft bearings at the ends and a ground steel shaft. The slide bearing consists of two parts, the bearing itself, which is the part of the assembly that is in...

UNIT TO STUDY A SPUR GEAR CUTAWAY MODEL - SGCM

Accessory of CMTM

Available

7.4.1.- CUTAWAY MODELS

SGCM

Unit to Study a Spur Gear Cutaway Model

Accessory of CMTM

The Unit to Study a Spur Gear Cutaway Model provides insight into the operation of this transmission system, characterized by teeth parallel to the axis of rotation, allowing for direct power transmission with high efficiency.This type of gear is...

UNIT TO STUDY A TWO-STAGE SPUR GEAR CUTAWAY MODEL - SGCM/2

Accessory of CMTM

Available

7.4.1.- CUTAWAY MODELS

SGCM/2

Unit to Study a Two-Stage Spur Gear Cutaway Model

Accessory of CMTM

The Unit to Study a Two-Stage Spur Gear Cutaway Model provides an in-depth analysis of these systems, which utilize two pairs of spur gears in series to achieve greater speed reduction and more efficient torque transmission.These systems are...

UNIT TO STUDY A VARIABLE SPEED TRAPEZOIDAL BELT DRIVE CUTAWAY MODEL - BDCM

Accessory of CMTM

Available

7.4.1.- CUTAWAY MODELS

BDCM

Unit to Study a Variable Speed Trapezoidal Belt Drive Cutaway Model

Accessory of CMTM

The Unit to Study a Variable Speed Trapezoidal Belt Drive Cutaway Model provides insight into the operation of continuously variable transmissions (CVT), where the speed ratio changes progressively and seamlessly, allowing for automatic torque...

UNIT TO STUDY A WORM GEAR CUTAWAY MODEL - WGCM

Accessory of CMTM

Available

7.4.1.- CUTAWAY MODELS

WGCM

Unit to Study a Worm Gear Cutaway Model

Accessory of CMTM

The Unit to Study a Worm Gear Cutaway Model provides insight into the operation of this transmission system, consisting of a helical worm screw and a circular cogwheel.This type of transmission is widely used in automatic doors, elevators, and...

Available

7.1.3.- STATICS AND DYNAMICS

SRI

Unit to Study Rotational Inertia

The Unit to Study Rotational Inertia, "SRI", has been designed to carry out tests to analyze the moments of inertia of a solid and a hollow cylinder, both with same mass and diameter. The moment of inertia of another hollow cylinder with different...

UNIT TO STUDY THE PRESSURE DROP OF COMPRESSIBLE FLUIDS IN PIPES - PDCFP

PDCFP

Available

8.8.- FLUID PIPING SYSTEM

PDCFP

Unit to Study the Pressure Drop of Compressible Fluids in Pipes

The Unit to Study the Pressure Drop of Compressible Fluids in Pipes, "PDCFP", allows the study of the compressible fluid pressure drop, for example the air of a compressor, and the different flow conditions (laminar and turbulent) thanks to the...

Available

7.3.2.1.- MECHANICAL TEST

MUP

Universal Buckling Unit

The Universal Buckling Unit "MUP" is a bench-top unit whose frame is made of anodized aluminum profiles and plates and steel elements, on which a bubble level is installed to equilibrate the system.The unit has been designed to carry out tests...

UNIVERSAL MATERIAL TESTING UNIT - EEU/20KN

EEU/20KN

Available

7.3.2.1.- MECHANICAL TEST

EEU/20KN

Universal Material Testing Unit

The Universal Material Testing Unit, "EEU/20KN", designed by EDIBON, is a didactic bench-top universal material testing unit. It is distinguished by its rigid construction, accurate control and a precise hydraulic system to apply loads of up to 20...

Available

7.1.6.- STRUCTURAL MECHANICS

MVV

Unsymmetrical Cantilever Unit

The system consists of a vertical cantilever rigidly clamped at its lower end to the main column which is attached to a rigid structure. Beams of different sections may be used.A loading head, located at the upper end of the column, can rotate...

VENTURI, BERNOULLI AND CAVITATION UNIT - FME22

FME22

Available

8.1.4.- HYDRODYNAMICS

FME22

Venturi, Bernoulli and Cavitation Unit

The Venturi, Bernoulli and Cavitation unit, "FME22", has been designed by EDIBON to demonstrate some of the practical possibilities that can be achieved with a Venturi tube.This unit is designed for demonstrating some practical possibilities with...

MVRE

Available

7.1.4.- VIBRATIONS AND OSCILLATIONS

MVRE

Vibration of Coil Spring Unit

The Vibration of Coil Spring Unit, "MVRE", has been designed by EDIBON to study and understand a coil torsion spring, a mass-spring system and the fundamental properties of its characteristic periodic motion.In this sense, the unit consists of a...

VIBRATIONS AND/OR DEFORMATIONS TEST MODULE - BS1

Accessory of BS

Available

6.1.2.1.- SENSORS AND ELECTRONIC INSTRUMENTATION

BS1

Vibrations and/or Deformations Test Module

Accessory of BS

Vibrations and/or Deformations Test Module, "BS1" has been designed to teach mechanical vibration and displacement variable measurement techniques.On the upper side of the test module there is a girder or elastic/vibrant sheet that is the one...

VOLTAGE TRANSFORMER FUNDAMENTS APPLICATION FOR PROTECTION DEVICES - AEL-VTFP

AEL-VTFP

Available

5.6.2.- PROTECTION SYSTEMS

AEL-VTFP

Voltage Transformer Fundaments Application for Protection Devices

The Voltage Transformer Fundaments Application for Protection Devices, "AEL-VTFP", has been designed by EDIBON to show the students which the main functions of voltage transformers are and which the parameters that must be considered in order to...

FME30/I

Available

8.1.2.- MEASUREMENT

FME30/I

Vortex Flow Meter

The Vortex Flowmeter, "FME30/I", designed by EDIBON, allows to perform different studies and experiments of various volumetric and mass flow measurement methods, as well as the comparison of continuous and discontinuous methods.This unit includes...

FME15

Available

8.1.8.- HYDRAULIC PIPING SYSTEM

FME15

Water Hammer

With the Water Hammer unit, "FME15", designed by EDIBON, we can demonstrate the effects of the instantaneous or gradual variation of the velocity of a fluid.The water hammer phenomenon, which appears as a consequence of a rapid change in the...

Available

9.2.- HEATING, VENTILATION, AIR CONDITIONING AND HOT WATER

WHT

Water Heaters Training Unit

The Water Heater Training Unit, "WHT", allows demonstrating the operation of three types of water heaters. The unit has three heaters, two of them commercial one with electronic ignition and one in millivolt, and a residential gas heater without...

WHEEL AND DIFFERENTIAL AXLE UNIT - MRYE2

MRYE2

Available

7.1.3.- STATICS AND DYNAMICS

MRYE2

Wheel and Differential Axle Unit

The Wheel and Differential Axle Unit, "MRYE2", has been designed by EDIBON to investigate the mechanics of a wheel and differential axle mechanism and demonstrating the force reduction on a differential pulley block.A wheel, consisting of a pulley...

MEER

Available

7.1.4.- VIBRATIONS AND OSCILLATIONS

MEER

Whirling of Shafts Unit

The Whirling of Shafts Unit, "MEER", has been designed by EDIBON to demonstrate and determine different modes of oscillation and resonance of shafts with continuous distribution of mass under different conditions.The operation of the Whirling of...

MBM2

Available

7.1.2.1.- MECHANISMS

MBM2

Whitworth Quick Return Mechanism

The Whitworth Quick Return Mechanism, "MBM2", is a mechanism able to transform circular movement into reciprocating movement. It ismade of aluminum and consists of a rotary element, called crank, with a graduated disk, connected to a rigid bar,...

MINI-EEE

Available

5.3.3.- WIND ENERGY

MINI-EEE

Wind Energy Basic Unit

The Wind Energy Basic Unit, "MINI-EEE", is a small-scale unit designed to study wind energy and the influence of some factors on its generation.This unit consists of a transparent tunnel, a wind turbine with rotor to place up to six blades and a...

WIND ENERGY DRIVE TRAIN ANALYSIS UNIT - WEDTA

WEDTA

Available

5.3.3.- WIND ENERGY

WEDTA

Wind Energy Drive Train Analysis Unit

The Wind Energy Drive Train Analysis Unit, "WEDTA", designed by EDIBON, allows students and professors to explore the operational characteristics of a wind turbine rotor under various wind conditions, thus optimizing the design and operation of...

FOR FURTHER INFORMATION, CONTACT US