The Transparent Vortex Flow Meter, "FME30", designed by EDIBON allows to perform studies and experiments of different volumetric and mass flow measurement methods, as well as the comparison of continuous and discontinuous methods.This unit...

The Tribology Modular Unit, "MEMT", consists of a base unit with electronic console and a series of experimental units to investigate and visualize tribological phenomena.MEMT-UB. Drive Unit for Tribological Tests. This unit is common for the...

The Tubular Flow Reactor, "QRFT," specifically designed by EDIBON, is intended for the kinetic study of liquid-liquid homogeneous reactions. This unit allows for a wide range of practices, including the determination of kinetic equations, the...

Heat exchangers with turbulent flow are widely used in various industries such as chemical, food, pharmaceutical, and energy generation. These devices play a fundamental role in heating and cooling fluids, as well as in cooling systems for...

The Two Hinged Arch Unit, "MFL", designed by EDIBON allows to study the response of an arched beam when an external load is applied on it.The arch is supported on two supports, a fixed one and a movable one. The displacement and horizontal...

The "N-EM" are a series of emulators that provide the students the required hardware to emulate the most common automatic systems.The "N-EM" modules are designed to work with the "AE-PLC" units to obtain the fundamental knowledge of PLC...

With the U-Shape Double Manometer, "HMM-W500," designed by EDIBON, the study of different pressures is facilitated for operation with the Pitot tube. The U-Shape Double Manometer allows finding the pressure between two points or two fluids.The...

The U-Shape Manometer, "HMM-U1000," designed by EDIBON, allows the study of various pressures and their relationship with the fluid. It measures the difference in liquid level in its columns, providing vital information for pressure analysis in...

The Underfloor Heating and/or Heat Source for Heat Pump, "UHHS", designed by EDIBON, allows the visualization of a piping system that simulates a radiant floor heating system and its functions as a heat sink. It can also be used as a heat source...

The Unit for Studying Bearing Friction, "MBF", has been designed by EDIBON to study sliding friction in slide bearings and rolling bearings. Since rolling friction is very little, rotational dynamics basic tests can be performed with the inertia...

The Unit for studying Deformation of Trusses, "MFCS3", allows the measurement of the stresses in the bars in different types of trusses, and the study of the dependence of the external force and the comparison of the experimental forces in the...

The Unit for studying Equilibrium of Moments on a Two Arm Lever,"MEMB2", allows to study the fundamentals of the equilibrium of moments and the application of the law of levers on a two-arm lever.A pivoted beam in the extreme of a vertical support...

The Unit for studying Forces in a Jib Crane, "MFPG", is designed to study the tensile and compressive forces in a planar central force system based on the example of a crane jib.The unit represents a planar central force system in which multiple...

The Unit for Studying Forces in a Simple Bar Structure, "MFBS", designed by EDIBON allows the study of forces acting on a simple truss when is subjected to a point load in one of the nodes that make up the structure.It consists of a group of five...

The Unit for studying Forces in an Overdeterminate Truss, "MFCS2", allows the measurement of the bar forces in a statically determinate truss and in a statically overdeterminate truss, the study of the distribution of forces in the single plane...

The Unit for studying Forces in Different Single Plane Trusses, "MFCS1", allows the measurement of the bar forces in various single plane trusses, the study of the dependency on the external force and the comparison of the experimental bar forces...

The Unit for studying Hooke's Law, "MELH", demonstrates the application of Hooke's Law and allows the visualization of the deformation of tension springs under load and the performance of oscillation experiments on a spring – mass system.The...

The Unit for studying Methods to Determine the Elastic Line, "MDLE", consists of set of beams, several supports (with clamp fixing and dial gauges, and with force gauge), a device to generate a bending moment, fixed pulleys, dial gauges and a set...

The Unit for the Kinematic Study of Gear Trains, "KSGT", unit includes a pivoting rail with a fixed axle to which two more axles can be fixed in any position in function of the feature to study.The cogwheels may be assembled on the axles in...

The Unit for the Study of Porous Beds in Venturi Tubes (Darcy´s Equation), "FME24", designed by EDIBON, for the study of porous beds in Venturi tubes (Darcy's Equation), allowing the complete and detailed understanding of this equation.The unit is...

It is a control gear. Its function is to control the space between teeth.

It is a mitre gear. It is made up of bevel gears that consist of two conical cogwheels. This device is used to transmit motion between two perpendicular shafts.

It is a multiple-disk clutch. Multiple-disk clutches allow for transmitting higher torques. Such clutches are used in the steering of chain tractors.

It is a planetary gear. It consists of one or more external or planet gears that revolves about a central or sun gear. Planetary gears are normally used as reducers in gearboxes or as differentials.