Channel, through which water flows, of rectangular section with transparent walls that enable to observe all the experiments. Water is taken from the storage tank by means of a hydraulic pump, with speed regulation, and, by the pipe, it is driven...

The Fluid Properties Unit, "FME35", designed by EDIBON, allows the study of the fluids fundamental properties that affect their behavior in practical applications.We can study capillarity, density and relative density (specific gravity), buoyancy...

The Fluid Statics and Manometry, "FME34", designed by EDIBON, allows the study of static fluids and manometry providing the user with an introduction in the behavior of liquids under hydrostatic conditions (fluids at standstill) and the...

The Hydrostatics Bench and Fluid Properties, "BHI", is a compact, mobile and independent unit.There is a water storage tank, to work in a closed system, at the bottom of the bench. The water is distributed by hand pumps from this tank to two upper...

The Fluidization and Fluid Bed Heat Transfer Unit, "TTLFB", has been designed to provide visual and quantitative results related to the flow of air through a packed bed and a fluidized bed made of granular material. It provides clear experimental...

The Flow Visualization in Channels unit, "FME09", designed by EDIBON, allows the visualization of liquid spillage phenomena in weirs and the study of objects submerged in a fluid stream (aerodynamics).The unit consists of a transparent...

The "RYC-C" Flow Rate Control module has been designed to study a practical control system, through the flow rate of a close water circuit.The "RYC-C" module consists of two main components: the "RYC-C" apparatus and the "RYC-C" interface box. The...

The Flow Meter Demonstration, "FME18", designed by EDIBON, allows through 3 different flow measurement accessories: Venturi tube, orifice plate and a variable area meter installed in series in the unit, the study to find the flow rate of the fluid...

The Flow Meters Demonstration Unit, "FMDU", designed by EDIBON demonstrates the important characteristics of fifteen types of flow meters used in the measurement of water flow through pipes or open channels.The main elements are a service module...

The objective of Flow Test Module, "BS4", is to show techniques to measure changeable fluids.The module is made up of two tanks assembled on a structure. In one of them there is a pumping system that allows to pump the water from the reserve tank,...

The Demonstration Infiltration Unit, "PEDI", has been developed for the comparative study of infiltration processes in the laboratory, which are essential for the study of any form of irrigation. Water movement through the soil can be seen and...

The Liquid/Solid Mixing Unit "EMLS" is made up of a main support frame, in which a dynamo brake motor of adjustable speed and mechanical connections are installed. Diverse types of agitators can be coupled to the motor.The motor with the above...

The Liquid-Liquid Extraction Unit, "UELL", is a laboratory scale unit designed to study the separation of the components of liquid mixtures by contact of the mixture with an immiscible solvent in which these components are preferentially...

The QDTL is a teaching unit that allows the students to familiarise with the notions of mass transfer theory, specially the diffusion in liquid systems, obtaining experimental data and results which are very useful for an ideal practice...

The Liquid level Test Module, "BS6", has been designed to teach the use and applications of level sensors and their measurement systems. This module teaches techniques to measure and control the liquid level in a tank.On this there is a two tanks...

The Deep Bed Filter Unit, "EFLP", allows us to filter a fluid in order to eliminate particles in suspension, to have it in more adequate conditions for its subsequent use or consumption.The pump takes raw water from one of the reservoirs of the...

The Transparent Vortex Flow Meter, "FME30", designed by EDIBON allows to perform studies and experiments of different volumetric and mass flow measurement methods, as well as the comparison of continuous and discontinuous methods.This unit...

The "RYC-TE" Temperature Control module has been designed to study a practical control system, through the control of the water temperature in a tank.The "RYC-TE" module consists of two main components: the "RYC-TE" apparatus and the "RYC-TE"...

The Temperature Measurement Training Unit, "TEMT", allows to compare the response of several devices to measure the temperature for different flows and different installation position of these devices.The unit includes four different measuring...

The Temperature Measurement Unit, "TMT", works as a temperature meter that uses different temperatures measuring devices to compare, check and analyze the temperature and how is the precision for the measure and for the device that the student has...

The Temperature Test Module, "BS2", has been designed to teach the use and applications of sensors of temperature as a measure, and its control.We have a half-open space in whose interior there are two lamps that are going to heat that space....

The Deflection of Curved Bars Unit "MDB" consists of a structure of aluminum and steel that allows the incorporation of different curved bars to be studied. It allows tests with curved bars of different shape.The use of two dial gauges placed...

With the Pilot Plant for the Production of Cured Products and Sausages, "CA00/CUPS", designed by EDIBON, we are able to obtain cured products from untreated meat following the following process:First, the meat that has been weighed and cleaned of...

The Reactive Power Compensation Application, "AEL-RPC", has been designed to study the reactive power effects in AC circuits, due to reactive loads, and its compensation procedures.Reactive power can be described as the quantity of "unused" power...

The Complete Home Automation Application with ZigBee Wireless Protocol, "AEL-AD28A", is a cutting-edge home automation application.It consists of a set of modules designed to cover different areas within the home automation field: emergency...

The objective of the Light Test Module, "BS10", is to show some of the techniques used to measure light or illumination intensity.The module is equipped with a lamp whose light intensity can be controlled by the variation of the voltage...

With the Pilot Plant for the Production of Cooked Pieces and Sausages, "CA00/COPS", designed by EDIBON, we are able to obtain cooked products from untreated meat, following the following process:To prepare this type of product, the first step is...

Heat exchangers are widely used in refrigeration, air conditioning, heating, energy generation, chemical processing, etc. They have many applications in engineering and, as a consequence, there are many models adapted to each application to obtain...

The Heat Transfer Series, "TSTCB", has been designed by EDIBON to study and compare different types of heat transfer on a small scale.It allows a wide range of heat transfer demonstrations and study the factors affecting and problems associated...

Bomb Calorimeter, "TBCF", comprises the calorimeter, a calorimeter vessel, an outer double walled water jacket, control unit to switch on/off the stirrer and the ignition device, an accurate thermometer and charging unit with pressure gauges to...