7.1.6.- 構造メカニズム

構造メカニズム UNITS
1-23 を表示中 合計 23 商品
UNIT FOR STUDYING FORCES IN A JIB CRANE - MFPG
  • MFPG
Available
7.1.6.- 構造メカニズム
MFPG
ジブクレーンフォース測定実験装置
The Unit for studying Forces in a Jib Crane, "MFPG", is designed to study the tensile and compressive forces in a planar central force system based on the example of a crane jib.The unit represents a planar central force system in which multiple...
SUSPENSION BRIDGE UNIT - MVS
  • MVS
Available
7.1.6.- 構造メカニズム
MVS
サスペンションブリッジ実験装置
The Suspension Bridge Unit, "MVS", consists of a deck and two parallel main cables that simulate a suspension bridge and allow the study of stress in the main cables. The deck of the bridge is simulated by a light alloy beam that is held by both...
PARABOLIC ARCH UNIT - MARP
  • MARP
Available
7.1.6.- 構造メカニズム
MARP
パラボラアーチ実験装置
The Parabolic Arch Unit "MARP" contains a pre-shaped articulated arch, which can be subjected to point or evenly distributed loads by means of seven uniformly distributed cables (cords) with hangers.One support of the arch is fixed whereas the...
THREE-HINGED ARCH UNIT - MART
  • MART
Available
7.1.6.- 構造メカニズム
MART
3ヒンジアーチ実験装置
The Three-Hinged Arch Unit "MART" allows the student to become familiar with three-hinged arches, to calculate the bearing forces (for point load, for uniformly distributed load and for moving load), to investigate the influence of the load on the...
UNIT FOR STUDYING DEFORMATION OF TRUSSES - MFCS3
  • MFCS3
Available
7.1.6.- 構造メカニズム
MFCS3
トラスひずみ測定実験装置
The Unit for studying Deformation of Trusses, "MFCS3", allows the measurement of the stresses in the bars in different types of trusses, and the study of the dependence of the external force and the comparison of the experimental forces in the...
THICK WALLED CYLINDER UNIT - MCPG
  • MCPG
Available
7.1.6.- 構造メカニズム
MCPG
Thick Walled Cylinder Unit
In the Thick-Walled Cylinder Unit, "MCPG", the stresses are determined through the measurement of the strains produced on the surface. These strains are measured by strain gauges.The thick-walled vessel consists of an aluminum cylinder of length...
TWO HINGED ARCH UNIT - MFL
  • MFL
Available
7.1.6.- 構造メカニズム
MFL
2ピンアーチ実験装置
The Two Hinged Arch Unit, "MFL", designed by EDIBON allows to study the response of an arched beam when an external load is applied on it.The arch is supported on two supports, a fixed one and a movable one. The displacement and horizontal...
PORTAL FRAME UNIT - MPO
  • MPO
Available
7.1.6.- 構造メカニズム
MPO
ポータルフレーム実験装置
The Portal Frame Unit, "MPO", allows to perform vertical deflection and horizontal deflection measurements in a fixed rectangular portal frames.To carry out the deflection tests, a series of loads with different weight must be applied to the...
STRESS HYPOTHESES UNIT - STH
  • STH
Available
7.1.6.- 構造メカニズム
STH
Stress Hypotheses Unit
The Stress Hypotheses Unit, "STH", allows the study and testing of stress hypotheses by applying loads in different directions on a test specimen point and measuring the deformations produced.Normal and shear stresses are applied, avoiding...
SIMPLE STABILITY PROBLEMS STUDY UNIT - MEPE
  • MEPE
Available
7.1.6.- 構造メカニズム
MEPE
単純安定性課題分析実験装置
The Simple Stability Problems Study Unit, "MEPE", has been designed to study the stability of a bar subjected to buckling by obtaining the critical load in different configurations. The unit consists of two bars of same length connected by a...
UNIT FOR STUDYING METHODS TO DETERMINE THE ELASTIC LINE - MDLE
  • MDLE
Available
7.1.6.- 構造メカニズム
MDLE
弾性ライン測定分析実験装置
The Unit for studying Methods to Determine the Elastic Line, "MDLE", consists of set of beams, several supports (with clamp fixing and dial gauges, and with force gauge), a device to generate a bending moment, fixed pulleys, dial gauges and a set...
THIN CYLINDER UNIT - MCD
  • MCD
Available
7.1.5.- 摩擦 (摩擦、 摩耗、 潤滑)
MCD
肉薄シリンダー実験装置
The Thin Cylinder Unit, "MCD", has been developed to enable the student to verify various analytical formulae with actual measured results. Strain gauges mounted in various positions and orientations on the cylinder provide an opportunity for...
UNIT TO STUDY STRESS ON A MEMBRANE - SSM
  • SSM
Available
7.1.6.- 構造メカニズム
SSM
Unit to Study Stress on a Membrane
The Unit to Study Stress on a Membrane, "SSM", designed by EDIBON, allows the study of stresses and deformations in a thin disc or membrane subjected to different compressive stresses.The main element of the equipment is a thin disc or membrane...
UNSYMMETRICAL CANTILEVER UNIT - MVV
  • MVV
Available
7.1.6.- 構造メカニズム
MVV
非対称カンチレバー実験装置
The system consists of a vertical cantilever rigidly clamped at its lower end to the main column which is attached to a rigid structure. Beams of different sections may be used.A loading head, located at the upper end of the column, can rotate...
DEFLECTION OF CURVED BARS UNIT - MDB
  • MDB
Available
7.3.2.1.- 機械的試験
MDB
湾曲棒たわみ実験装置
The Deflection of Curved Bars Unit "MDB" consists of a structure of aluminum and steel that allows the incorporation of different curved bars to be studied. It allows tests with curved bars of different shape.The use of two dial gauges placed...
BEAM DEFLECTION UNIT - MFV
  • MFV
Available
7.3.2.1.- 機械的試験
MFV
梁たわみ実験装置
The Beam Deflection Unit, "MFV" has been designed to enable the students to observe and study the following phenomena in simply supported beams and cantilever beams:Relation between the deflections and the applied loads.Effect of the length and...
STRUT BUCKLING UNIT - MFLT
  • MFLT
Available
7.3.2.1.- 機械的試験
MFLT
棒鋼の座屈を研究する機械
The Strut Buckling Unit "MFLT" allows the student to obtain experimentally the buckling critical load of slender struts subjected to compression.The unit allows to study the buckling of pieces of different lengths, ranging from 300 mm. to 625 mm.,...
EULER BUCKLING MODES UNIT - MEBM
  • MEBM
Available
7.3.2.1.- 機械的試験
MEBM
Euler Buckling Modes Unit
With the Euler Buckling Modes Unit, "MEBM", the four Euler buckling cases are demonstrated, for which four elastic bars are fixed or supported in a frame and subjected to compression load with a system of weights.The elastic bars can be free or...
リクエスト情報