MVS サスペンションブリッジ実験装置

7.1.6.- 構造メカニズム 14.1.6.- 構造メカニズム

革新的なシステム

The Suspension Bridge Unit, "MVS", consists of a suspended beam that simulates a suspension bridge and allows the experimental and theoretical comparison of the tensions of the cables and the study of the suspension of a bridge under different load conditions.

一般的な説明を表示

カタログ

コンテストの仕様

拡張

ICAI

対話型コンピューター支援命令ソフトウェア

MSAC

集録および制御モジュラーシステム

研究室

7TV

機械・自動車・材料研究室

7HE

高等教育のための機械・自動車・材料研究室

概要

The Suspension Bridge Unit, "MVS", consists of a deck and two parallel main cables that simulate a suspension bridge and allow the study of stress in the main cables.

The deck of the bridge is simulated by a light alloy beam that is held by both parallel main cables through bars that act as suspenders.

The suspenders are distributed at constant and relatively short distances. Loads are applied to the beam by coupling masses at a series of load points to simulate a distributed load.

These loads create some tensions in the suspenders that are supported by both main cables, and they transfer them to the pulleys, where those tensions are counteracted by hanging masses.

Set of weights and cords are supplied.

演習と指導の慣行

マニュアルに含まれるガイド付き実習

To demonstrate the characteristics of a bridge simplesuspension.
To observe the stability of a structure.
To examine the relation between loads applied and suspensioncable tension.
To determine the experimental value of the tension in thesupporting cables of a suspended beam subjected to auniform load distribution.
To compare the experimental and theoretical results.

補完的な機器

UNIT FOR STUDYING FORCES IN A JIB CRANE - MFPG

MFPG

Available

14.1.6.- 構造メカニズム

MFPG

ジブクレーンフォース測定実験装置

The Unit for studying Forces in a Jib Crane, "MFPG", is designed to study the tensile and compressive forces in a planar central force system based on the example of a crane jib. The unit represents a planar central force system in which...

MARP

Available

14.1.6.- 構造メカニズム

MARP

パラボラアーチ実験装置

The Parabolic Arch Unit "MARP" contains a pre-shaped articulated arch, which can be subjected to point or evenly distributed loads by means of seven uniformly distributed cables (cords) with hangers.One support of the arch is fixed whereas the...

MART

Available

14.1.6.- 構造メカニズム

MART

3ヒンジアーチ実験装置

The Three-Hinged Arch Unit "MART" allows the student to become familiar with three-hinged arches, to calculate the bearing forces (for point load, for uniformly distributed load and for moving load), to investigate the influence of the load on the...

UNIT FOR STUDYING FORCES IN A SIMPLE BAR STRUCTURE - MFBS

MFBS

Available

14.1.6.- 構造メカニズム

MFBS

単純棒構造における応力測定実験装置

The Unit for Studying Forces in a Simple Bar Structure, "MFBS", designed by EDIBON allows the study of forces acting on a simple truss when is subjected to a point load in one of the nodes that make up the structure. It consists of a group of five...

UNIT FOR STUDYING FORCES IN DIFFERENT SINGLE PLANE TRUSSES - MFCS1

MFCS1

Available

14.1.6.- 構造メカニズム

MFCS1

多様単平面トラスにおける応力測定実験装置

The Unit for studying Forces in Different Single Plane Trusses, "MFCS1", allows the measurement of the bar forces in various single plane trusses, the study of the dependency on the external force and the comparison of the experimental bar forces...

UNIT FOR STUDYING FORCES IN AN OVERDETERMINATE TRUSS - MFCS2

MFCS2

Available

14.1.6.- 構造メカニズム

MFCS2

多元トラスにおける応力測定実験装置

The Unit for studying Forces in an Overdeterminate Truss, "MFCS2", allows the measurement of the bar forces in a statically determinate truss and in a statically overdeterminate truss, the study of the distribution of forces in the single plane...

UNIT FOR STUDYING DEFORMATION OF TRUSSES - MFCS3

MFCS3

Available

14.1.6.- 構造メカニズム

MFCS3

トラスひずみ測定実験装置

The Unit for studying Deformation of Trusses, "MFCS3", allows the measurement of the stresses in the bars in different types of trusses, and the study of the dependence of the external force and the comparison of the experimental forces in the...

Available

14.1.6.- 構造メカニズム

MFL

2ピンアーチ実験装置

The Two Hinged Arch Unit, "MFL", designed by EDIBON allows to study the response of an arched beam when an external load is applied on it.The arch is supported on two supports, a fixed one and a movable one. The displacement and horizontal...

Available

14.1.6.- 構造メカニズム

MPO

ポータルフレーム実験装置

The Portal Frame Unit "MPO" allows to perform vertical deflection and horizontal deflection measurements in a fixed rectangular portal frames. To carry out the deflection tests, a series of loads with different weight must be applied to the...

SIMPLE STABILITY PROBLEMS STUDY UNIT - MEPE

MEPE

Available

14.1.6.- 構造メカニズム

MEPE

単純安定性課題分析実験装置

The Simple Stability Problems Study Unit, "MEPE", has been designed to study the stability of a bar subjected to buckling by obtaining the critical load in different configurations.The unit consists of two bars of same length connected by a...

UNIT FOR STUDYING METHODS TO DETERMINE THE ELASTIC LINE - MDLE

MDLE

Available

14.1.6.- 構造メカニズム

MDLE

弾性ライン測定分析実験装置

The Unit for studying Methods to Determine the Elastic Line, "MDLE", consists of set of beams, several supports (with clamp fixing and dial gauges, and with force gauge), a device to generate a bending moment, fixed pulleys, dial gauges and a set...

Available

14.1.5.- 摩擦 (摩擦、摩耗、潤滑)

MCD

肉薄シリンダー実験装置

The Thin Cylinder Unit, "MCD", has been developed to enable the student to verify various analytical formulae with actual measured results. Strain gauges mounted in various positions and orientations on the cylinder provide an opportunity for...

品質

アフターサービス

その他の情報については, お問い合わせください