The "RYC-CLM" Magnetic Levitation Control module has been designed to study a practical control system.The "RYC-CLM" module consists of two main components: the "RYC-CLM" apparatus and the "RYC-CLM" interface box. The "RYC-CLM" apparatus contains...

The Measurement and Regulation Station Trainer,"MRST", designed by EDIBON is a totally accessible bench-top unit. The unit works with an air compressor that simulates the gas flowing inside the pipes (air testing), allowing to check the tightness...

The Mesh in Pipe Unit, "AMT/P", consists of a Pipe network, a lateral panel where all the elements to test are located and a hydraulics bench, which has all the elements and accessories required for the unit to work autonomously.The valves that...

Vertical Multimanometer (8 Manometric Tubes, 500 mm in Length), "HMM-V500," designed by EDIBON, is a multimanometer designed to accurately measure and analyze pressure variations in vertical configurations. It provides valuable data to understand...

The Nozzle Pressure Distribution Unit, "TPT", allows to investigate the pressure distribution and the mass flow rate in nozzles (convergentdivergent and convergent nozzles).The unit includes three types of nozzles:Convergent type (conical) nozzle,...

Operational amplifiers are compact, active, linear and high-gain devices designed to provide the desired transfer function. An operational amplifier consists of an electronic circuit having two inputs and one output. The output is the difference...

Optoelectronics is the link between optical systems and electronic systems. Optoelectronic components are those whose operation is directly related to light.They are semiconductor devices capable of producing light radiation within the human...

Oscillators operation is usually very similar in all of them: the oscillating circuit produces an oscillation, then the amplifier increases it and finally the feedback network takes a part of the energy from the oscillating circuit and introduces...

The Overdrive Unit, "MEC", includes a set of epicyclical gears that represent an application of a simple epicyclic arrangement of the type used in a motor vehicle overdrive.Simple epicyclic set consists of:Sun gear that rotates together with the...

The "N-EM" are a series of emulators that provide the students the required hardware to emulate the most common automatic systems.The "N-EM" modules are designed to work with the "AE-PLC" units to obtain the fundamental knowledge of PLC...

The PANASONIC PLC Application, "AE-PLC-PAN", is a PLC unit designed by EDIBON which use one of the last PANASONIC PLC units. It allows the user to learn about PLC logic programming, different PLC programming languages, PLC to PC communication,...

The "RYC-pH" pH Control module has been designed to study a practical control system, through the pH dissolution control in a stirred tank.The "RYC-pH" module consists of two main components: "RYC-pH" apparatus and "RYC-pH" interface box. The...

The Photoelastic Stress Demonstration Unit, "PSD", consists of a frame on which the test specimens are placed. The specimens are made of a special transparent material that has a double optical refraction effect under the action of a mechanical...

The purpose of this application is the study of photovoltaic power plants in the context of microgrids. It consists of a three-phase inverter fed with a photovoltaic panel array simulator. The user will be able to set the generation parameters and...

The Pieces Feeder Workstation, "AE-PLC-APS", is a unit that works with pneumatics and electro-pneumatics technologies.The function of the "AE-PLC-APS" is to supply pieces and to verify them, if they are acceptable.The pieces will be supplied one...

The Pipe Network Unit, with Hydraulics Bench (FME00), "AMT", consists of a Pipe network, a lateral panel where all the elements to test are located and a hydraulics bench, which has all the elements and accessories required for the unit to work...

The Pipe Network Unit, without Hydraulics Bench (FME00), "AMT/B", consists of a Pipe network, a lateral panel where all the elements to test are located and a hydraulics bench, which has all the elements and accessories required for the unit to...

The Plate Clutch, "MEM", allows to demonstrate the influence of the friction surface and the applied pressure of the springs on the transmitted torque for a friction clutch. To this end, several clutch discs with different diameters and...

The Plate Heat Exchanger for TICC, "TIPL", designed by EDIBON, allows the study of heat transfer between hot and cold water flowing through alternate channels formed between parallel plates. This unit enables the analysis of how heat transfer...

The Pneumatic and Electro-Pneumatic Application, "AE-NS", is a modular application consisting of a great variety of optional kits and elements to configure the desired pneumatic and electro-pneumatic circuits.The optional pneumatic kits available...

The "AE-PLC-MACT" is an automatic handling station with conveyor system commanded by a PLC. The "AE-PLC-MACT" is composed by one pneumatic handling system that use vacuum technology to move the pieces from the input piece area to the conveyor...

The PFGA unit is a flue gas analyzer stored in a portable case. It is used to check the existence of O2, CO, CO2 and nitrogen oxides in the flue gases from home heating systems with simultaneous measurement of the flue gases temperature and the...

The "RYC-CP" Position Control module has been designed to study a practical control system, through the control of a linear position system.The "RYC-CP" module consists of two main components: the "RYC-CP" apparatus and the "RYC-CP" interface box....

Semiconductors used in power electronics operate as switches and therefore it is interesting to know the conduction characteristics, switching and control methods.With Power Electronics Module, "N-M9", designed by EDIBON, the operation of MOSFET...

The "RYC-P" Pressure Control module has been designed to study a practical control system, through the control of the air pressure level of an air pressure tank.The "RYC-P" module consists of two main components: the "RYC-P" apparatus and the...

The Pressure Measurement and Calibration Unit, "TMCP", has been designed to study the concept of pressure and the different methods and techniques used to measure this variable.The dead-weight calibrator consists of a cylinder in which interior a...

The Pressure Measurement Unit, "HEMP", enables a wide range of investigations and studies into pressure measurement techniques, using Bourdon type manometers and different U-tube manometers, to understand the operation, the characteristics of the...