8.1.- 流体力学模块化实验室

Hydraulics is the branch of science that deals with the mechanical properties of fluids, and Fluid Mechanics provides the foundation for hydraulics.With LIFLUBA (Basic Fluids Mechanics Integrated Laboratory), EDIBON tries to give answer to the...

The Hydraulics Bench, "FME00", designed by EDIBON, allows the study of fluid behaviour, hydraulic theory and the properties of fluid mechanics.It is formed by a movable hydraulics bench used to hold a wide variety of modules, which allow the...

The Basic Hydraulic Feed System, "FME00/B", designed by EDIBON is a service unit for different Fluid Mechanics Units as: "FME" type modules, Fluid Friction in Pipes Unit "AFT", etc., increasing the equipment profitability.

The Flow over Weirs, "FME02", designed by EDIBON, allows to study the flow characteristics trough a rectangular and "V" shaped neckline.This module has many elements that are used in combination with the Hydraulics Bench (FME00):A special...

The Pressure Gauge Calibrator, "FME10", designed by EDIBON, allows the study of the operation of a Bourdon type pressure gauge using a standard set of calibrated weights and the determination and the study of the pressure gauge hysteresis...

The Flow Meter Demonstration, "FME18", designed by EDIBON, allows through 3 different flow measurement accessories: Venturi tube, orifice plate and a variable area meter installed in series in the unit, the study to find the flow rate of the fluid...

The Depression Measurement System (vacuum gauge), "FME 26", is designed to be connected to the inlet of some flow aspiration system, in a way that we could measure the depression made by the so-called aspiration system. Such system will be...

The Transparent Vortex Flow Meter, "FME30", designed by EDIBON allows to perform studies and experiments of different volumetric and mass flow measurement methods, as well as the comparison of continuous and discontinuous methods.This unit...

The Vortex Flowmeter, "FME30/I", designed by EDIBON, allows to perform different studies and experiments of various volumetric and mass flow measurement methods, as well as the comparison of continuous and discontinuous methods.This unit includes...

The Static Pitot Tube, "FME32", designed by EDIBON, allows to analyze the change in flow rate inside a pipe.The Pitot static tube can be moved across the whole cross-section of the tube, and thus to measure the pressure profile.This tube is...

This module has been designed to study static fluids and manometry. It provides the user an introduction to the behaviour of liquids under hydrostatic conditions (fluids at rest) and to the application of those principles in the pressure...

The Rotameter, "FME36", designed by EDIBON is a variable area flowmeter with floater. This type of flowmeter can be used for flow measurements in almost any environment.The operation mode of this type of flowmeter is based on the fact that if a...

BDAS is designed to monitor the measurements of each module type "FME" from a computer.This system can monitor any module, checking the revolutions given by the water pump or the torque, differential pressures for Bernoulli theorems, pressure...

The module consists of a quadrant assembled to the arm of ascale that swings around an axis.When the quadrant is immersed in the water tank, the forcethat acts on the flat rectangular front surface exerts amomentum with respect to the supporting...

The Metacentric Height Demonstration Unit, "FME11", designed by EDIBON, allows the study of the stability of a floating object by calculating its metacentric height.The unit consists of a floating methacrylate prismatic base, on which a vertical...

The Metacentric Height Demostration of a "V" Shaped Floating Object, "FME11-A", designed by EDIBON, allows the study of the stability of a floating object by calculating the metacentric height of a floating object starting from a V-shaped floating...

The Metacentric Height Demostration of a "U" Shaped Floating Object, "FME11-B", designed by EDIBON, allows the study of the stability of a floating object by calculating its metacentric height starting from a U-shaped floating body.The unit...

The Pascal's Principle Demonstration Unit, "FME33", designed by EDIBON allows to demonstrate Pascal's principle, i.e. that the pressure in an incompressible fluid is independent of the column size section but depends only on its height (liquid...

The Fluid Properties Unit, "FME35", designed by EDIBON, allows the study of the fluids fundamental properties that affect their behavior (capillarity, density and relative density (specific gravity), buoyancy (Archimedes principle), viscosity,...

The Jet Impact on Surfaces unit, "FME01", designed by EDIBON, allows to obtain experimental force measurements exerted by a jet on different surfaces and to compare the values with the theoretical results.The unit consists of a cylindrical tank...

The Bernoulli's Theorem Demonstration unit, "FME03", designed by EDIBON is mainly composed of a circular section pipe with the shape of a truncated cone, transparent and with seven pressure taps that allows to measure, simultaneously, the static...

The Orifice Discharge Unit, "FME04", designed by EDIBON allows the study of the different concentration, discharge and velocity coefficients for thin and/or thick wall for different types: colloidal, Venturi or diaphragm.The unit consists of a...

The module has a cylindrical and transparent deposit with two inlet pipes diametrically opposed, slightly inclined to produce a whirl. This deposit has an outlet in the center of its base, where 3 mouthpieces with orifices of different...

The Orifice and Free Jet Flow unit, "FME17", designed by EDIBON, allows the study of the different discharge and velocity coefficients in permanent or variable regime as well as the calculation of the discharge times.The unit consists of a...

The Cavitation Phenomenon Demonstration unit, "FME19", designed by EDIBON is composed of a Venturi tube with a rectangular cross section, one of its sides being transparent, allowing a better visualization of the cavitation phenomenon.It includes...

The Venturi, Bernoulli and Cavitation unit, "FME22", has been designed by EDIBON to demonstrate some of the practical possibilities that can be achieved with a Venturi tube.This unit is designed for demonstrating some practical possibilities with...

The Osborne Reynolds Demonstration Unit, "FME06", designed by EDIBON, allows the study of the laminar, transitional and turbulent regime of a liquid by associating them with the respective Reynolds variable.The unit consists of a cylindrical tank...

The Flow Visualization in Channels unit, "FME09", designed by EDIBON, allows the visualization of liquid spillage phenomena in weirs and the study of objects submerged in a fluid stream (aerodynamics).The unit consists of a transparent...

The Laminar Flow Demostration unit, "FME20", designed by EDIBON, allows a complete study of the bi-dimensional problems associated with laminar flow. Thanks to an efficient system of dye injection we can observe the different models of flow. It...

The Flow Channel, lenght: 1 m, "FME25", designed by EDIBON, allows to study of the water behavior flowing through a channel.It basically consists of a channel of rectangular cross section with transparent walls, through which water flows.It has a...