9TV 技术和职业教育的热力学和热力学实验室

The main element of the Computer Controlled Hot Water Production and Heating Teaching Unit, "EACC", is the boiler. Its function is the heating of the water that will flow through the other elements transferring its heat. It is a low temperature...

The Computer Controlled Solar/Heat Source Vapour Turbine, "HTVC", has been designed to provide an easily understood vapour power plant and to demonstrate, on a lab scale, the ability to produce shaft power from Solar Radiation.It is a bench-top...

The Maintenance Kit containing Vacuum Pump, Hoses and Manometers, "T/KIT1", contains the necessary elements to carry out the loading and unloading of a cooling system.The system consists of a vacuum pump, spark free to avoid fire hazards, which...

The Maintenance Kit containing Leakage Detector, "T/KIT2", includes a portable detector sensitive to concentrations of all commercial refrigerants with the objective of locating leaks in refrigeration systems. Refrigerants detectable by the kit...

The Computer Controlled Air Conditioning Laboratory Unit, "TAAC", has been designed to study the change of the air conditions and the refrigeration circuit.The unit consists of a testing tunnel made of stainless steel, in which there have...

The Computer Controlled Automobile Air Conditioning Trainer, "TAAUC", consists, basically, of a compressor driven through a belt by a motor that simulates the engine of a car.The number of revolutions of the engine and, therefore, the compressor,...

The Computer Controlled Air Conditioning Unit with Climatic Chamber and Water Chiller, "TACC", is an actual air conditioning system with climatic chamber suitable for people and allows the study of the influence of different operation modes of the...

The Computer Controlled Recirculating Air Conditioning Unit, "TARC", has been designed to study both the changes in the air conditions and the refrigeration circuit. For that purpose, temperature sensors, pressure sensors and flow meters have been...

Bomb Calorimeter, "TBCF", comprises the calorimeter, a calorimeter vessel, an outer double walled water jacket, control unit to switch on/off the stirrer and the ignition device, an accurate thermometer and charging unit with pressure gauges to...

Measurement of the volumetric concentrations according to the procedure of nondispersiva infrared absorption.Engines selection: gasoline, butane, propane, 2/4 times, 1/2/3/4/5/6/8/12 cylinders.Fast warm-up of the measure cell.Auto-check...

The Computer Controlled Exhaust Gas Calorimeter, "TBMC-CG", is mounted on a laminated aluminium profiles frame and panels in painted steel.The main element consists on a double-wall tank made in stainless steel. Through the tank interior the...

The Computer Controlled Test Bench for Single-Cylinder and Two-Cylinders Engines, 11 kW, "TBMC12", designed by EDIBON, is a teaching unit to test internal combustion engines of up to 11 kW.The element of the unit that offers load torque is an eddy...

The Computer Controlled Test Bench for Single-Cylinder Engines, 2.2 kW, "TBMC3", designed by EDIBON, is a teaching unit to test internal combustion engines of up to 2.2 kW.The unit has an element to exert the braking torque, an asynchronous motor...

The Computer Controlled Test Bench for Four Cylinders Engines, 75 kW, "TBMC75", designed by EDIBON, is a teaching unit to test internal combustion engines of up to 75 kW.The element of the unit that offers load torque is an eddy current...

The Computer Controlled Test Bench for Single-Cylinder Engines, 7.5 kW, "TBMC8", designed by EDIBON, is a teaching unit to test internal combustion engines of up to 7.5 kW.The element of the unit that offers load torque is an eddy current...

The Computer Controlled Thermo-Electric Heat Pump, "TBTC", allows the study of different phenomena in which heat and electricity take place (Thermoelectricity).Some of them are the Peltier effect, the Thomson or Lenz effect and the Seebeck effect....

The Computer Controlled Heat Conduction Unit, "TCCC", consists of two modules electrically heated. One of the modules is provided of a cylindrical metal bar for the realization of a series of experiments of linear heat conduction. While the...

The Computer Controlled Boiling Heat Transfer Unit, "TCEC", consists of a heating element horizontally mounted inside a vertical glass chamber submerged in coolant. This heating element is connected to a cylindrical copper sleeve in contact with...

The Computer Controlled Separating and Throttling Calorimeter, "TCESC", has been designed to determine the steam humidity content and the dryness fraction of steam.This unit works with steam. The steam is introduced into the line by means of a...

The Computer Controlled Free and Forced Convection Heat Transfer Unit, "TCLFC", allows to study the efficiency of different exchangers, analyzing the heat transmission coefficients of each exchanger exposed to different airflows.Fan placed in the...

The Computer Controlled Thermal Conductivity of Liquids and Gases Unit, "TCLGC", has been designed to allow the students to appreciate and understand the heat transfer process through any gas or liquid locked in a solid. By the realization of the...

The Computer Controlled Thermal Conductivity of Building and Insulating Materials Unit, "TCMC", is a unit employed to measure thermal conductivity of low-conductivity materials, such as insulating materials.This unit is a calibrated instrument...

The Computer Controlled Film and Dropwise Condensation Unit, "TCPGC", has been specially designed for students use and to provide visual results and quantitative results related to heat transfer during condensation. Self-contained unit, which has...

Cooling plant at teaching and industrial level, with modular design, and computer controlled. Plant with ice store, wet cooling tower and dry cooler.

The Computer Controlled Refrigeration Cycle Demonstration Unit, "TCRC", allows the demonstration of vapour compression refrigeration and heat pump cycle with visual observation of all important processes.Thanks by utilising a non-toxic refrigerant...

The diesel power generating set with integrated control and monitoring system has been developed by Edibon to conduct studies and research on the operation process of real power plants running with diesel gensets. This equipment is composed of two...

The Computer Controlled Marcet Boiler Unit "TECMC" is an unit designed to demonstrate the relationship between pressure and temperature of the saturated steam for comparison with published results.The unit consists of an insulated stainless steel...

The Thermal Expansion Training Unit, "TEDT", allows to study the thermal expansion of different pipe sections and the thermal expansion force. It comprises original components as used in heating and sanitation systems. This unit provides...

The Sanitary Fittings Training Unit, "TEIS", has been designed by EDIBON for training in the plumbing sector. It consists of an anodized aluminum frame and panels in painted steel in which tests can be carried out with the most common systems of...

The Pipe Cleaning Training Unit, "TELT", designed by EDIBON, simulates a real house piping system, so original components used in plumbing systems are employed.The objective of this unit is to study the cleaning of pipes from the sanitation...

The Temperature Measurement Training Unit, "TEMT", allows to compare the response of several devices to measure the temperature for different flows and different installation position of these devices.The unit includes four different measuring...

The "TEPGC" is a unit designed to demonstrate the expansion and compression processes of a perfect gas and the basic principles of thermodynamics. The unit consists of two rigid vessels connected to each other. They are made of methacrylate to...

The Three-Way Mixing Valve Training Unit, "TEV3V", allows to demonstrate the function of a three-way mixing valve in a hot water heating system. The three-way mixing valve in the heating system regulates the supply water temperature to a heating...

The Four-Way Mixing Valve Training Unit, "TEV4V", allows to demonstrate the function of a four-way mixing valve in a hot water heating system. The four-way mixing valve in the heating system regulates the circulation and feed flow temperatures of...

The Computer Controlled Flow Boiling Demonstration Unit, "TFEC", has as main component an experimental tube made of two glass concentric tubes. In these tubes two fluids flow crosscurrent: refrigerant, which flows by convection and in an...

The Computer Controlled Laminar/Viscous Flow Heat Transfer Unit, "TFLVC", is a laboratory scale unit designed to study heat transfer between hot oil flowing in laminar flow through an internal tube and cold water that flows through the annulus...

The Computer Controlled Nozzle Performance Test Unit, "TFTC", has been specially designed to allow students to investigate and study the performance of a nozzle (kinetic energy and thrust). Operating from a normal laboratory compressed air...

This filtration unit has been designed to study the filtration process with two different types of filters. On one hand, there is a vertical plate filter consisting of nylon plates with a diameter of 5 microns, used to filter a known concentration...

The main element of the "TGDEPC" unit is the High Pressure Turbine, which is also called Gas Generative Turbine. It consists of: - Radial compressor, which is feeded by atmospheric air to compress it. - Tubular combustion chamber. In every...

The main element of the "TGFAC" unit is the gas turbine, which consists of:Axial compressor, supplied by atmospheric air that will be compressed afterwards.Annular combustion chamber, where fuel is added to the compressed air and that mixture is...

It is an electrically heated steam generator (3 kW electric resistance). The resistor has an internal thermostat at 150ºC.This type of generator produces steam for an operating pressure of 0.9 bar, with a maximum pressure of 2 bar.The maximum...

The THALAC/1 has been designed to allow the students to understand the behaviour and characteristics of a heat pump (with air evaporator and water condenser) working in the steam compression cycle and with three compressors connected in...

The Computer Controlled Heat Pump + Air Conditioning + Refrigeration with 2 Condensers and 2 Evaporators (Water/Air)), "THAR22C", has as aim introduce the student to the study of the heat pumps, air conditioning and refrigeration, as well as the...

The Computer Controlled Capacity Control Methods in Refrigeration, "THARA2C/1", allows to study and to investigate several methods of capacity control. For this purpose a refrigeration circuit with two refrigeration chambers is available in which...

The Computer Controlled Rerversible Heat Pump + Air Conditioning + Refrigeration with 2 Condensers and 2 Evaporators (Water/Air),"THIBAR22C", has as aim introduce the student to the study of the heat pumps, air conditioning and refrigeration, as...

The Computer Controlled Water-to-Air Heat Exchanger Unit, "TIAAC", includes a stainless steel duct with a heat exchanger in its center and a centrifugal fan at one end. The fan impels the air through the heat exchanger. The heat exchanger...

The Drinking Water Installation Unit, "TIAP", has been designed to demonstrate domestic water heating from the cold water supply. A typical domestic drinking water system is attached to the front panel of the unit. The unit includes the most...

Heat exchangers are widely used in refrigeration, air conditioning, heating, energy generation, chemical processing, etc. They have many applications in engineering and, as a consequence, there are many models adapted to each application to obtain...

Cross Flow Heat Exchanger for TICC: Designed to study heat transfer between two fluids in cross flow configuration. Hot water flow coming from the base unit enters and leaves a radiator perpendicular to an air current, which is generated by a fan.

Shell and Tube Heat Exchanger for TICC: It consists of a series of tubes inside the heat exchanger where hot water flows. The cooling water flows through the space between the inner tubes and the shell.

The Computer Controlled Cross Flow Heat Exchanger (TIFCC) basically consists of a rectangular wind tunnel made of stainless steel, resistant to corrosion. It has a bell-shaped inlet and a central opening arranged longitudinally with two supporting...

Turbulent Flow Heat Exchanger for TICC: Let us study the heat transfer between hot water that circulates through an internal tube and cold water that flows through the annular zone between the internal and the external tube.

Plate Heat Exchanger for TICC: It has been designed to study the heat transfer between hot water and cold water flowing through alternate channels formed between parallel plates.

Concentric Tube Heat Exchanger for TICC: It has been designed to study the heat transfer between hot water flowing through an internal tube and cold water flowing through the annular area between the internal and the external tubes.

This unit is common for Heat Exchangers type "TI" and can work with one or several exchangers.This unit performs the following tasks:Heating water in a computer controlled thermostatic bath.Pumping the hot water.Regulation and measurement of the...

The Computer Controlled Steam to Water Heat Exchanger, "TIVAC", is a unit designed to study condensation phenomena in shell and tube heat exchangers. It mainly consists of a steam chamber, which is a vertical cylinder made of resistant glass. The...

Jacketed Vessel Heat Exchanger for TICC: Allows the study of heat transfer between hot water flowing through a jacket and thecold water contained in a vessel.

Coil Vessel Heat Exchanger for TICC: Allows the study of heat transfer between hot water flowing through a coil and cold water contained in the vessel.

The Computer Controlled Gas Laws Unit (Boyle and Gay-Lussac Law), "TLBGC", allows to demonstrate two fundamental gas laws: Boylend Mariotte's Law (isothermal change of state) and Gay-Lussac's 2 Law (isochoric change of state).The unit consists of...

The Pressure Measurement and Calibration Unit, "TMCP", has been designed to study the concept of pressure and the different methods and techniques used to measure this variable.The dead-weight calibrator consists of a cylinder in which interior a...

The Air Humidity Measurement Unit, "TMHA", enables the differences in accuracy between different instruments to measure the air relative humidity. It also includes a fan to show the effects of airflow on the different instruments. A mobile...

The Computer Controlled Test Bench for Hybrid Engine, "TMHC", is a teaching unit that allows to study and analyze the power source of a hybrid vehicle, consisting on a combination of an electrical motor and an internal combustion engine.These two...

The Computer Controlled Stirling Motor, "TMSC", is used to demonstrate the operation of a thermodynamic machine for the conversion of energy. It converts thermal energy into mechanical energy and operates as a motor (heat engine). Additionally it...

The Temperature Measurement Unit, "TMT", works as a temperature meter that uses different temperatures measuring devices to compare, check and analyze the temperature and how is the precision for the measure and for the device that the student has...

The Protection of Drinking Water Training Unit, "TPAP", has been designed by EDIBON to study cases in which the drinking water system is contaminated with wastewater. It is specially designed for the training of students in the plumbing sector.The...

The Computer Controlled Contact Plate Freezer, "TPCC", allow the student to freeze food products quickly by using an industrial freezing process. The unit includes a compression refrigeration circuit. It is based on mechanically forcing the...

The Nozzle Pressure Distribution Unit, "TPT", allows to investigate the pressure distribution and the mass flow rate in nozzles (convergentdivergent and convergent nozzles).The unit includes three types of nozzles:Convergent type (conical) nozzle,...

The Computer Controlled Vortex Tube Refrigerator Unit, "TPVC", is a unit designed to study the physical, mechanical and thermodynamic characteristics of a vortex tube.This unit works with compressed air. The air, previously filtered to remove...

The Computer Controlled Absorption Refrigeration Unit, "TRAC", designed by EDIBON, is a complete laboratory unit for the demonstration of absorption refrigeration.This unit is provided with a dual power source (heat source) of LPG and electricity....

The Computer Controlled Refrigeration Circuit with Variable Load, "TRCAC", is a unit designed for the study of a refrigeration cycle with an thermal adjustable load.The unit includes all the components required for a fully operational...

The Computer Controlled Refrigeration Unit with Open Compressor is arranged in a clear way and represents a typical compression refrigeration system with open compressor:The main elements of the unit are:Open compressor activated by an electric...

The Computer Controlled Vapour-Compression Refrigeration Unit, "TRCVC", allows the understanding of the vapor-compression refrigeration process by changing the operation of the different parts of the process, and to study the response of the...

The main element of the Computer Controlled Two Doors Domestic Refrigeration Unit, "TRD2PC", is a combifridge freezer with transparent panels to observe all the elements of a refrigeration cycle: compressor, filter,evaporator, condenser,...

The Computer Controlled Recycle Loops Unit, "TRLC", has been designed to demonstrate, both visually and experimentally, what a recycleloop is and how it works. It has many teaching applications, among them the performance of mass and energy...

The objective of the Computer Controlled Refrigeration Unit with Refrigeration and Freezing Chamber "TRRC" designed by EDIBON is to introduce the student into the complex world of refrigeration systems, as well as to study and determine the...

The Computer Controlled Thermal Radiation and Light Radiation Unit, "TRTC", has been designed to demonstrate the laws of radiant heat transfer and radiant heat exchange. It basically consists in two independent parts. One of the parts is for the...

The Computer Controlled Air Conditioning Unit with Climatic Chamber, "TSAC", designed by EDIBON, is clearly arranged and represents a complete air conditioning system with an air duct and a climatic chamber.The main components of the air...

With the Computer Controlled Air Duct Systems Unit, "TSCAC", the user will study the air distribution under different configurations thanks to the supports included with the unit. The user himself will assemble the air ducts using usual elements...

With the Sewerage Unit, "TSID", tests about a wastewater sanitation system can be made and the flow in a sewage system can be observed.A complete sewage system can be observed with the "TSID" unit. The collection of wastewater from a series of...

The Computer Controlled Saturation Pressure Unit, "TSPC", consists of a water boiler, including a computer controlled immersion heating element, and a sight glass to observe the boiling patterns in the water surface and control the water level...

The Computer Controlled Heat Transfer Series, "TSTCC", has been designed by EDIBON to study and compare different types of heat transfer on a small scale. It allows a wide range of heat transfer demonstrations and study the factors affecting and...

The Computer Controlled Bench Top Cooling Tower, "TTEC", includes a pump that impels hot water from a tank (with level switch and heating element) to the manifolds located at the top of the cooling tower. Water flow can be adjusted by a manual...

The Computer Controlled Fluidization and Fluid Bed Heat Transfer Unit, "TTLFC", has been designed to provide visual and quantitative results related to the flow of air through a packed bed and a fluidized bed made of granular material. It provides...

The Computer Controlled Steam Turbine, "TTVC", consists of a single stage impulse steam turbine. It includes an injector, a brake, a water cooled condenser, safety mechanisms and all the necessary controls and instrumentation.The steam passes...

The Computer Controlled Combustion Laboratory Unit, "TVCC", unit is mounted on a metallic frame that enables safe access to the equipment and an easy handling and access to the burner, combustion chamber and all the accessories and control panels....

The Computer Controlled Flame Propagation and Stability Unit, "TVPLC", is a teaching unit which allows to obtain various flames by changing the quantities of the fuel – comburent mix. The unit is prepared to work with different gaseous fuels, so...