The Osborne Reynolds Horizontal Demonstration Unit, "FME31", designed by EDIBON, allows to study the characteristics of a liquid flowing through a pipe and the Reynolds number in each of the liquid states.The FME31 unit makes it possible to study...

The Pelton Turbine unit, "FME16", designed by EDIBON, allows the study of the characteristics of the tangential wheels or pressure turbines commonly used to produce electricity in hydroelectric plants to exploit large hydraulic jumps of low...

Energy generation from water flows is the most exploited renewable energy source in the world for obtaining electricity, due to its simplicity of operation and its adaptability to different environments. The orography of the terrain is essential...

With the Water Hammer unit, "FME15", designed by EDIBON, we can demonstrate the effects of the instantaneous or gradual variation of the velocity of a fluid.The water hammer phenomenon, which appears as a consequence of a rapid change in the...

The Automotive Sensors Unit, "AV-S", provides a practical solution to familiarize the students with the sensors used in modern automotive systems.The Automotive Sensors Unit, "AV-S", is composed of real sensors and components used in current...

The Automotive Fundamental Electronic Circuits Unit, "AV-EC", provides a practical solution to the introduction of electronics in the automotive field with a group of common circuits used in the automobiles nowadays.The circuits included in the...

The Automotive Fundamental Electrical Circuits Unit, "AV-ELC", provides a practical solution to the introduction of electricity in the automotive field with a group of common circuits used by the automobiles today.The circuits included in the...

The Automotive Starting and Charging Systems unit, "AV-SCS", has been designed by EDIBON to provide theoretical and practical trainingin the field of electrical starting and charging systems for motor vehicles. This unit aims to provide students...

The Automotive Auxiliary Components Unit, "AV-AC", provides a practical solution to obtain advance knowledge in the electronic and electric systems used in the automotive field today.All sensors and actuators included in the "AV-AC" unit are...

The Automotive Wiper Washer Unit, "AV-WW", provides a practical solution to the introduction of the components of the wiper washer system used in the automotive field nowadays.The components included in the "AV-WW" are focused on different...

The Automotive Actuators Unit, "AV-A", provides a practical solution to become familiar with the actuators used in today’s automobiles.The Automotive Actuators Unit, "AV-A", is composed by real actuators and components used in present automotive...

The Sedimentation Tank, "PDS", is a teaching unit, designed by EDIBON, to demonstrate the sedimentation process and to familiarize with the settling principle of discrete particles settling into a tank. It will also allow to study the hydraulic...

The Biogas Process Unit, "EBGB", is supplied with two packed anaerobic digesters. In this way, the user can work either in only one stage or in two stages, separating the different phases of the digestion process (the processes of hydrolysis,...

The Depression Measurement System (vacuum gauge), "FME 26", is designed to be connected to the inlet of some flow aspiration system, in a way that we could measure the depression made by the so-called aspiration system. Such system will be...

The Sedimentation Study Unit, "ESED", designed by EDIBON, allows studying and compare the sedimentation processes of several suspensions simultaneously.It is formed by five sedimentation methacrylate cylinders mounted vertically on a panel,...

The Sediment Transport Demonstration Channel, "CAS", designed by EDIBON, consist of an inclinable channel mounted on a base plate, supported by two supports, with a discharge tank and recirculating pump. This tank is in the Basic Hydraulic Feed...

The Pumping Storage Power Plant Application, with SCADA, "AEL-GAD-01S", has been developed by Edibon to study the pumped storage power stations and their applications. Pumping Storage Power Plants Applications are a type of hydroelectric energy...

Pump cavitation is produced when steam cavities are created within a fluid in which forces act responding to the pressure differences.Cavitation causes noise, damage to components and loss of performance.The Set to Study Cavitation in Pumps,...

The Fluid Properties Unit, "FME35", designed by EDIBON, allows the study of the fluids fundamental properties that affect their behavior in practical applications.We can study capillarity, density and relative density (specific gravity), buoyancy...

The Flow Channels, "CFG", are hydrodynamic channels to perform multiple hydraulic tests. They consist of a rectangular section channel with tempered glass transparent walls through which water flows. Water is impelled by a pump from the storage...

Channel, through which water flows, of rectangular section with transparent walls that enable to observe all the experiments. Water is taken from the storage tank by means of a hydraulic pump and, by the pipe, it is driven to the inlet tank, where...

Channel, through which water flows, of rectangular section with transparent walls that enable to observe all the experiments. Water is taken from the storage tank by means of a hydraulic pump, with speed regulation, and, by the pipe, it is driven...

The Computer Controlled Flow Channels, "CFGC", are hydrodynamic channels to perform multiple hydraulic tests. They consist of a rectangular section channel with tempered glass transparent walls through which water flows. Water is impelled by a...

The Flow Channel, lenght: 1 m, "FME25", designed by EDIBON, allows to study of the water behavior flowing through a channel.It basically consists of a channel of rectangular cross section with transparent walls, through which water flows.It has a...

The Fluid Statics and Manometry, "FME34", designed by EDIBON, allows the study of static fluids and manometry providing the user with an introduction in the behavior of liquids under hydrostatic conditions (fluids at standstill) and the...

The Flow Visualization in Channels unit, "FME09", designed by EDIBON, allows the visualization of liquid spillage phenomena in weirs and the study of objects submerged in a fluid stream (aerodynamics).The unit consists of a transparent...

The objective of Flow Test Module, "BS4", is to show techniques to measure changeable fluids.The module is made up of two tanks assembled on a structure. In one of them there is a pumping system that allows to pump the water from the reserve tank,...

The Flow Meters Demonstration Unit, "FMDU", designed by EDIBON demonstrates the important characteristics of fifteen types of flow meters used in the measurement of water flow through pipes or open channels.The main elements are a service module...

The Flow Meter Demonstration, "FME18", designed by EDIBON, allows through 3 different flow measurement accessories: Venturi tube, orifice plate and a variable area meter installed in series in the unit, the study to find the flow rate of the fluid...