MTB Torsionsgerät.

7.3.2.1.- MECHANISCHE TESTS 14.1.8.- MECHANISCHE TESTS

INNOVATIVE SYSTEME

To perform the tests a metallic rod is fastened by clamps and subjected to the testing force.

Allgemeine Beschreibung anzeigen

Katalog

Wettbewerbsspezifikationen

Erweiterungen

ICAI

Interaktive Computerunterrichtssoftware

MSAC

Modulares Erfassungs- und Steuerungssystem

Laboratorien

7TV

Mechanik-, Automobil- und Werkstofflabor für technische und berufliche Bildung

7HE

Mechanik-, Automobil- und Werkstofflabor für die Hochschulausbildung

ÄHNLICHE NEUIGKEITEN

ALLGEMEINE BESCHREIBUNG

To perform the tests a metallic rod is fastened by clamps and subjected to the testing force. Force is gradually applied on the rod to observe the elastic tension generated.

The force moment or torque is applied by a dynamometer with a lever. Deformation generated by the torsional stress is obtained by reading a dial gauge in contact with the arm. The torsional deformation angle is obtained by a simple trigonometric identity, providing the unit with important didactic characteristics.

Steel, brass and aluminum rods are supplied to perform the practical exercises. Additionally, rods made of other materials can be employed.

ÜBUNGEN UND GEFÜHRTE PRAKTIKEN

GEFÜHRTE PRAKTISCHE ÜBUNGEN IM HANDBUCH ENTHALTEN

Verification of the elastic torsion equation of circular rods.
Experimental determination of the relationship between thetorsion moment and the shaft angular determination.
Experimental determination of the relationship between the testrod length and the shaft turn angle for a same torsional force.
Experimental determination of the calue of the Modulus ofRigidity for steel, brass and aliminum.

ERGÄNZENDE AUSRÜSTUNG

UNIVERSAL MATERIAL TESTING UNIT - EEU/20KN

EEU/20KN

Available

7.3.2.1.- MECHANISCHE TESTS

EEU/20KN

Testgerät für universelle Werkstoffe.

The Universal Material Testing Unit, "EEU/20KN", is a didactic bench-top universal material testing unit. It is distinguished by its rigid construction, accurate control and a precise hydraulic system to apply loads of up to 20 kN, which enables...

EEDB

Available

7.3.2.1.- MECHANISCHE TESTS

EEDB

Gerät zur Prüfung der Brinellhärte.

The Brinell Hardness Testing Unit, "EEDB", is a hardness tester that determines Brinell hardness in metals, hard alloys, tempered steels, etc. Besides, it can be used with other materials, such as rigid plastics, bakelite, etc.A penetrating ball...

BRINELL, VICKERS & ROCKWELL HARDNESS TESTING UNIT - EBVR

EBVR

Available

7.3.2.1.- MECHANISCHE TESTS

EBVR

Brinell, Vickers und Rockwell-Härte-Testgerät

The Brinell, Vickers and Rockwell Hardness Testing Unit, "EBVR", consists of a hardness testing machine that determines the three main types of hardness (Brinell, Vickers and Rockwell). It can be adapted to determine hardness of ferrous materials...

EEFCR

Available

7.3.2.1.- MECHANISCHE TESTS

EEFCR

Kriechversuchgerät.

The Creep Testing Unit ,EEFCR, for the creep testing is mounted on a structure of aluminum profiles which a painted steel panel is supported on.The EEFCR unit is designed to carry out experiments on specimens of plastic materials. Due to the...

COMPUTER CONTROLLED FATIGUE TESTING UNIT - EEFC

EEFC

Available

7.3.2.1.- MECHANISCHE TESTS

EEFC

Computergesteuertes Ermüdungstestgerät.

The Computer Controlled Fatigue Testing Unit, "EEFC", designed by EDIBON, allows to study the fatigue strength of the materials. For that purpose, fatigue tests are performed with different materials and notches.Optionally, with the additional...

Available

7.3.2.1.- MECHANISCHE TESTS

EEF

Ermüdungstestgerät.

The Fatigue Testing Unit, "EEF", designed by EDIBON, allows to study the fatigue strength of the materials. For that purpose, fatigue tests are performed with different materials and notches.Optionally, with the additional recommended element Set...

CHARPY AND IZOD IMPACT TESTING UNIT - EEICI

EEICI

Available

7.3.2.1.- MECHANISCHE TESTS

EEICI

Gerät für den Versuch nach Charpy und Izod.

The Charpy and Izod Impact Testing Unit “EEICI” consists of a pendulum supported on bearings with an arm of 330 mm long and a fastening system in the initial position of the test. The suitable hammer either for Charpy or Izod test is screwed to...

Available

7.3.2.1.- MECHANISCHE TESTS

MUP

Gerät zur Belastung von Strebebalken.

The Universal Buckling Unit "MUP" is a bench-top unit whose frame is made of anodized aluminum profiles and plates and steel elements, on which a bubble level is installed to equilibrate the system.The unit has been designed to carry out tests...

MFLT

Available

7.3.2.1.- MECHANISCHE TESTS

MFLT

Strebebalkengerät.

The Strut Buckling Unit "MFLT" allows the student to obtain experimentally the buckling critical load of slender struts subjected to compression.The unit allows to study the buckling of pieces of different lengths, ranging from 300 mm. to 625 mm.,...

Available

7.3.2.1.- MECHANISCHE TESTS

MTP

Verdrill- und Biegemaschine.

The Torsion and Bend Unit, "MTP", is a combined apparatus for the demonstration of both torsion and bend to be used in the laboratory or as a complement of the theoretical study about torsion and bend. Its size and weight facilitate its transport...

MTTU

Available

7.3.2.1.- MECHANISCHE TESTS

MTTU

Tensile Tester Unit

With the Tensile Tester Unit, "MTTU", tensile test can be performed. A specimen made of different materials is subjected to an increasing axial tensile stress till failure. This unit allows the user to perform tensile tests with different...

Available

7.3.2.1.- MECHANISCHE TESTS

MDB

Gerät für die Durchbiegung bei gekrümmten Balken.

The Deflection of Curved Bars Unit "MDB" consists of a structure of aluminum and steel that allows the incorporation of different curved bars to be studied. It allows tests with curved bars of different shape.The use of two dial gauges placed...

QUALITÄT

KUNDENDIENST

FÜR WEITERE INFORMATIONEN, KONTAKTIEREN SIE UNS