It has been designed to study the heat transfer between hot water flowing through an internal tube and cold water flowing through the annular area between the internal and the external tubes.

The Concentric Tube Heat Exchanger for TICC, "TITC", designed by EDIBON, allows for the study of heat transfer between two fluids: the hot water flowing through the inner tube and the cold water flowing through the annular zone between the inner...

The Jacketed Vessel Heat Exchanger for TICC, "TIVE", designed by EDIBON, provides a comprehensive environment for the detailed study of heat transfer between two non-mixing fluids. In this unit, hot water flows through a jacket, transferring heat...

The Coil Vessel Heat Exchanger for TICC, "TIVS", designed by EDIBON, provides a comprehensive environment for the detailed study of heat transfer between two non-mixing fluids. In this unit, hot water circulates through a coil, transferring heat...

The Static Pitot Tube, "FME32", designed by EDIBON, the change in flow speed within a tube can be determined.The Pitot static tube can be moved across the whole cross-section of the tube, and thus to measure the pressure profile.This tube is...

The Flow Visualization Aerodynamic Tunnel, "TAVF180/100", consists of a vertical conduction in which an upward flow of air and smoke is induced, which passes through different models allowing to study the behavior of the flow around it. Thus it is...

The Aerodynamic Tunnel for Flight Demonstration, "TADV225/450", consists of an open wind tunnel in whose working section the model of an aircraft with fixed wings is located. The aircraft is piloted by the user using controls similar to those of a...

Aerodynamics is the part of fluid mechanics that studies the motion of gases and the forces or reactions to which the bodies they interact with are subjected. Aerodynamics is not only important by itself but also as a complement to aeronautics....

The Computer Controlled Aerodynamic Tunnel, 300 x 300 mm, "TA300/300C", is a wind tunnel designed to study subsonic aerodynamics in a tunnel in open circuit and with incompressible subsonic flow. Air is drawn by a variable speed fan, computer...

The Computer Controlled Aerodynamic Tunnel, 50 x 250 mm, "TA50/250C", is a wind tunnel designed to study subsonic aerodynamics in a tunnel in open circuit and with incompressible subsonic flow. Air is drawn by a variable speed fan, computer...

Aerodynamics is the part of fluid mechanics that studies the motion of gases and the forces or reactions to which the bodies they interact with are subjected. Aerodynamics is not only important by itself but also as a complement to aeronautics....

The Computer Controlled Supersonic Wind Tunnel (Three Blowers), "TAS25/100C-3B", is an open wind tunnel for the study of theaerodynamic properties of different drag bodies subject to subsonic and supersonic flows. Airflows through three vacuum...

The Computer Controlled Supersonic Wind Tunnel, "TAS25/100C", is an open wind tunnel for the study of the aerodynamic properties of different drag bodies subject to subsonic and supersonic flows. Air flows through a vacuum pump or blower...

With the Axial Turbine, "FME27", designed by EDIBON, it is possible to study and to understand the axial flow turbines which, unlike the radial flow turbines, the working fluid is parallel to the axis of rotation.This unit consists of an axial...

The Computer Controlled Axial Flow Turbine, "TFAC", consists of a small-scale turbine with single-stage axial flow input. It has eight nozzles that act as water rings to the rotor, four of which have an incidence angle of 20º and the other four of...

The Radial Flow Turbine unit, "FME21", designed by EDIBON, allows the study of a turbomachine, specifically radial turbines capable of handling slower flow levels than other turbine models.This unit consist of a miniature Radial Turbine with two...

The Computer Controlled Radial Flow Turbine, "TFRC", consists of a small-scale radial flow turbine with two nozzles at 90 degrees to the perpendicular direction of the axis of rotation.In order to raise the fluid, it has a computer controlled pump...

The main element of the Computer Controlled Two-Shaft Gas Turbine "TGDEC" is the High Pressure Turbine, which is also called Gas Generative Turbine. It consists of:Radial compressor, which is feeded by atmospheric air to compress it.Tubular...

The main element of the Computer Controlled Two-Shaft Gas Turbine/ Jet Engine, "TGDEPC", is the High Pressure Turbine, which is also called Gas Generative Turbine. It consists of:Radial compressor, which is feeded by atmospheric air to compress...

The main element of the "TGFAC" unit is the gas turbine, which consists of:Axial compressor, supplied by atmospheric air that will be compressed afterwards.Annular combustion chamber, where fuel is added to the compressed air and that mixture is...

The Computer Controlled Solar/Heat Source Vapour Turbine, "HTVC", has been designed to provide an easily understood vapour power plant and to demonstrate, on a lab scale, the ability to produce shaft power from Solar Radiation.It is a bench-top...

The Computer Controlled Steam Turbine, "TTVC", consists of a single stage impulse steam turbine. It includes an injector, a brake, a water cooled condenser, safety mechanisms and all the necessary controls and instrumentation.The steam passes...

The Computer Controlled Experimental Impulse Turbine, "HTIC", allows to study the characteristics and the behavior of a small scale impulse turbine.This unit includes suitable instrumentation to measure the main parameters:There is a pressure...

The Experimental Reaction Turbine, Computer Controlled (PC), "HTRC", allows to study the characteristics of operation of a small scale reaction turbine.This unit includes suitable instrumentation to measure the main parameters:There is a pressure...

With the Francis Turbine unit, "FME28", designed by EDIBON, we study the Francis turbines commonly used when we have average flow rates and heights.This unit consists on a miniature Francis turbine. The water inlet flow is controlled by a valve...

The Computer Controlled Francis Turbine, "TFC", consists of a small-scale Francis Turbine, with a valve that allows flow regulation and has a ring with adjustable guide vanes that allows control of the angle of incidence of the water in the...

With the Kaplan Turbine unit, "FME29", designed by EDIBON, we study the Kaplan turbines commonly used when we have high flow rates but low flow height.This unit consists on a miniature Kaplan turbine. The water inlet flow is controlled by a valve...

The Computer Controlled Kaplan Turbine, "TKC", consists of a small-scale Kaplan turbine that has a ring with adjustable guide vanes, which allow the control of water flow in the turbine.In order to raise the fluid, it has a computer controlled...

The Pelton Turbine unit, "FME16", designed by EDIBON, allows the study of the characteristics of the tangential wheels or pressure turbines commonly used to produce electricity in hydroelectric plants to exploit large hydraulic jumps of low...

The Computer Controlled Pelton Turbine, "TPC", designed by EDIBON, consists of a small-scale Pelton turbine, with a valve that allows the flow to be regulated. The turbine includes a PELTON runner with 16 buckets, which can be clearly seen through...