Terlaris

Menampilkan 745 -756 dari 950 produk

BRINELL, VICKERS & ROCKWELL HARDNESS TESTING UNIT - EBVR

EBVR

Available

7.3.2.1.- UJI MEKANIK

EBVR

Peralatan Uji Kekerasan "Brinell", "Vickers" dan "Rockwell"

The Brinell, Vickers and Rockwell Hardness Testing Unit, "EBVR", designed by EDIBON, consists of a hardness testing machine that determines the three main types of hardness (Brinell, Vickers and Rockwell). It can be adapted to determine hardness...

Available

7.3.2.1.- UJI MEKANIK

EEF

Peralatan Uji Kelelahan

The Fatigue Testing Unit, "EEF", designed by EDIBON, allows to study the fatigue strength of the materials. For that purpose, fatigue tests are performed with different materials and notches.Optionally, with the additional recommended element Set...

COMPUTER CONTROLLED FATIGUE TESTING UNIT - EEFC

EEFC

Available

7.3.2.1.- UJI MEKANIK

EEFC

Peralatan Uji Kelelahan, Dikendalikan dari Komputer (PC)

The Computer Controlled Fatigue Testing Unit, "EEFC", designed by EDIBON, allows to study the fatigue strength of the materials. For that purpose, fatigue tests are performed with different materials and notches.Optionally, with the additional...

COMPUTER CONTROLLED TWO-STAGE COMPRESSOR TEST UNIT - HCDEC

HCDEC

Available

8.7.5.- KOMPRESOR

HCDEC

Peralatan Uji Kompresor Dua Tahap, Dikendalikan dari Komputer (PC)

The Computer Controlled Two-Stage Compressor Test Unit, "HCDEC", works with compressed air and presents as a principal device a compression bench with two pistons, low and high pressure.This unit presents four circuits or work dispositions which...

UNIVERSAL MATERIAL TESTING UNIT - EEU/20KN

EEU/20KN

Available

7.3.2.1.- UJI MEKANIK

EEU/20KN

Peralatan Uji Material Universal

The Universal Material Testing Unit, "EEU/20KN", designed by EDIBON, is a didactic bench-top universal material testing unit. It is distinguished by its rigid construction, accurate control and a precise hydraulic system to apply loads of up to 20...

MTTU

Available

7.3.2.1.- UJI MEKANIK

MTTU

Peralatan Uji Tarik

With the Tensile Tester Unit, "MTTU", designed by EDIBON, tensile test can be performed. A specimen made of different materials is subjected to an increasing axial tensile stress till failure. This unit allows the user to perform tensile tests...

Available

7.3.2.1.- UJI MEKANIK

MTT

Peralatan Uji Torsi (30Nm)

The Torsion Test Unit (30Nm), "MTT", designed by EDIBON, has a shaft attached to the test specimen where the moment of torsion is measured with strain gauges. By means of an angle measuring sensor it is possible to determine the torsion angle....

COMPUTER CONTROLLED BIOMEDICAL ULTRASOUND THERMAL EFFECTS TEACHING UNIT - BIUTEC

BIUTEC

Available

14.3.- PERALATAN BIOMEDIS

BIUTEC

Peralatan Ultrasonografi dalam Biomedis, Dikendalikan dari Komputer (PC)

The Computer Controlled Biomedical Ultrasound Thermal Effects Teaching Unit, "BIUTEC", has been designed by EDIBON to study, in an experimental way, the ultrasound effects in biological tissues and acquire the necessary knowledge to design and...

Available

7.3.2.1.- UJI MEKANIK

MUP

Peralatan Universal untuk Tekuk

The Universal Buckling Unit "MUP" is a bench-top unit whose frame is made of anodized aluminum profiles and plates and steel elements, on which a bubble level is installed to equilibrate the system.The unit has been designed to carry out tests...

CORIOLIS FORCE DEMONSTRATION UNIT - MDFC

MDFC

Available

7.1.3.- STATICS AND DYNAMICS

MDFC

Peralatan untuk Demonstrasi Gaya Coriolis

The Coriolis Force Demonstration Unit, "MDFC", designed by EDIBON, is used to observe the deflection of a jet of water generated by a pump attached to a rotating arm that rotates to different speeds in a horizontal plane. An electronically...

COMPUTER CONTROLLED CRITICAL SPEED INVESTIGATION UNIT - MVCC

MVCC

Available

7.1.4.- GETARAN DAN OSILASI

MVCC

Peralatan untuk Penelitian Kecepatan Kritis, Dikendalikan dari Komputer (PC)

Some phenomena that appear in mechanical systems, such as vibration, self-centering and resonance in rotary shafts, can be clearly demonstrated with the Computer Controlled Critical Speed Investigation Unit, "MVCC".The operation of the "MVCC" unit...

UNIT FOR DETERMINING THE GAUGE FACTOR OF STRAIN GAUGES - MFGE

MFGE

Available

7.3.1.- FOTOELASTISITAS DAN PENGUKURAN STRAIN

MFGE

Peralatan untuk Penentuan Faktor Strain Gauge

The Unit for Determining the Gauge Factor of Strain Gauges, "MFGE", designed by EDIBON, allows to determine the k factor of strain gauges.The bar rests on two supports with ball bearings, so that it is possible to work with a load under pure...

UNTUK INFORMASI LEBIH LANJUT, HUBUNGI KAMI