7.3.- TEKNIK MATERIAL

Teknik material adalah cabang ilmiah dan industri yang bertanggung jawab untuk membuat interpretasi industri dari ilmu material. Secara antropologis, berbagai tahapan manusia pengembangan telah diklasifikasikan menurut bahan yang digunakan dalam pembuatan alat (Zaman Batu, Zaman Perunggu, dll.). Dengan demikian, perkembangan umat manusia terkait erat dengan studi tentang bahan baru.

Lihat Lebih Banyak

Selama 200 tahun terakhir, penemuan tentang material, yang mengungkapkan kontribusi dari Gibbs, telah dibuat. Dia mendemonstrasikan adanya hubungan antara properti material dan strukturnya. Penemuan ini telah memungkinkan pengembangan materi baru, seperti graphene, dan penyelidikan bidang baru, seperti nanomaterial atau nanoteknologi.

Sejumlah besar pengujian telah dilakukan untuk mencapai tingkat pengembangan tersebut, termasuk pengujian tekukan mekanis, pengujian kekerasan (Rockell, Brinell, Vickers, Martens), uji torsi, uji tarik (ketangguhan dan ketahanan), uji tarik (creep ), pengujian geser, serta uji kimia (perlakuan termal, struktur internal, dll.). Demikian pula, bahan dapat diklasifikasikan sebagai:

  • Logam (ferrous dan non-ferrous).
  • Keramika.
  • Polimer (termoplastik, plastik termoseting, dan elastomer).
  • Bahan komposit.

Penerapan kemajuan ini terbukti di berbagai area industri, seperti otomotif, elektronik, dirgantara, aeronautika dan biomedis, sehingga memberikan teknik material pentingnya hal tersebut dalam masyarakat saat ini.

Lihat Produk
Materi Terkait
TEKNIK MATERIAL UNITS
Menampilkan 1 -29 dari 29 produk
PHOTOELASTICITY UNIT - EFO
  • EFO
Available
7.3.1.- FOTOELASTISITAS DAN PENGUKURAN STRAIN
EFO
Unit Fotoelastisitas
Unit for photoelasticity practices, illustrating the subjects of the Photoelasticity theory, the Elasticity theory, Strength of Materials, and Structure theory.It is very suitable for the introduction and study of photoelasticity: optical...
COMPUTER CONTROLLED PHOTOELASTICITY UNIT WITH ARTIFICIAL VISION SYSTEM - EFOV
  • EFOV
Available
7.3.1.- FOTOELASTISITAS DAN PENGUKURAN STRAIN
EFOV
Unit Fotoelastisitas dengan Sistem Visi Buatan
Unit for photoelasticity practices, illustrating the subjects of the photoelasticity theory, the elasticity theory, strength of materials, and structure theory.It is very suitable for the introduction and study of photoelasticity: optical...
STRAIN GAUGE TRAINING UNIT - MEGE
  • MEGE
Available
7.3.1.- FOTOELASTISITAS DAN PENGUKURAN STRAIN
MEGE
Strain Gauge Training Unit
The Strain Gauge Training Unit, "MEGE", provides an introduction to the fundamentals of measurement with strain gauges, to compare how resistance strain gauges work and how they measure strains in different structures (torsion, tension and bending...
UNIT FOR DETERMINING THE GAUGE FACTOR OF STRAIN GAUGES - MFGE
  • MFGE
Available
7.3.1.- FOTOELASTISITAS DAN PENGUKURAN STRAIN
MFGE
Unit for determining the Gauge Factor of Strain Gauges
The Unit for Determining the Gauge Factor of Strain Gauges, "MFGE", allows to determine the k factor of strain gauges.The bar rests on two supports with ball bearings, so that it is possible to work with a load under pure bending.To perform such...
PHOTOELASTIC STRESS DEMONSTRATION UNIT - PSD
  • PSD
Available
7.3.1.- FOTOELASTISITAS DAN PENGUKURAN STRAIN
PSD
Photoelastic Stress Demonstration Unit
The Photoelastic Stress Demonstration Unit, "PSD", consists of a frame on which the test specimens are placed. The specimens are made of a special transparent material that has a double optical refraction effect under the action of a mechanical...
UNIVERSAL MATERIAL TESTING UNIT - EEU/20KN
  • EEU/20KN
Available
7.3.2.1.- UJI MEKANIK
EEU/20KN
Unit Tes Material Universal
The Universal Material Testing Unit, "EEU/20KN", is a didactic bench-top universal material testing unit. It is distinguished by its rigid construction, accurate control and a precise hydraulic system to apply loads of up to 20 kN, which enables...
BRINELL HARDNESS TESTING UNIT - EEDB
  • EEDB
Available
7.3.2.1.- UJI MEKANIK
EEDB
Unit Tes Brinell Hardness
The Brinell Hardness Testing Unit, "EEDB", is a hardness tester that determines Brinell hardness in metals, hard alloys, tempered steels, etc. Besides, it can be used with other materials, such as rigid plastics, bakelite, etc.A penetrating ball...
BRINELL, VICKERS & ROCKWELL HARDNESS TESTING UNIT - EBVR
  • EBVR
Available
7.3.2.1.- UJI MEKANIK
EBVR
Unit Tes Brinell, Vickers dan Rockwell Hardness
The Brinell, Vickers and Rockwell Hardness Testing Unit, "EBVR", consists of a hardness testing machine that determines the three main types of hardness (Brinell, Vickers and Rockwell). It can be adapted to determine hardness of ferrous materials...
CREEP TESTING UNIT - EEFCR
  • EEFCR
Available
7.3.2.1.- UJI MEKANIK
EEFCR
Unit Tes Creep
The Creep Testing Unit, "EEFCR", for the creep testing is mounted on a structure of aluminum profiles which a painted steel panel is supported on.The "EEFCR" unit is designed to carry out experiments on specimens of plastic materials. Due to the...
COMPUTER CONTROLLED FATIGUE TESTING UNIT - EEFC
  • EEFC
Available
7.3.2.1.- UJI MEKANIK
EEFC
Unit Komputer Kontrol Tes Kelelahan
The Computer Controlled Fatigue Testing Unit, "EEFC", designed by EDIBON, allows to study the fatigue strength of the materials. For that purpose, fatigue tests are performed with different materials and notches.Optionally, with the additional...
FATIGUE TESTING UNIT - EEF
  • EEF
Available
7.3.2.1.- UJI MEKANIK
EEF
Unit Tes Kelelahan
The Fatigue Testing Unit, "EEF", designed by EDIBON, allows to study the fatigue strength of the materials. For that purpose, fatigue tests are performed with different materials and notches.Optionally, with the additional recommended element Set...
CHARPY AND IZOD IMPACT TESTING UNIT - EEICI
  • EEICI
Available
7.3.2.1.- UJI MEKANIK
EEICI
Unit Tes Impact "Charpy dan Izod"
The Charpy and Izod Impact Testing Unit, "EEICI", consists of a pendulum supported on bearings with an arm of 330 mm long and a fastening system in the initial position of the test. The suitable hammer either for Charpy or Izod test is screwed to...
UNIVERSAL BUCKLING UNIT - MUP
  • MUP
Available
7.3.2.1.- UJI MEKANIK
MUP
Universal Buckling Unit
The Universal Buckling Unit "MUP" is a bench-top unit whose frame is made of anodized aluminum profiles and plates and steel elements, on which a bubble level is installed to equilibrate the system.The unit has been designed to carry out tests...
STRUT BUCKLING UNIT - MFLT
  • MFLT
Available
7.3.2.1.- UJI MEKANIK
MFLT
Unit Strut
The Strut Buckling Unit "MFLT" allows the student to obtain experimentally the buckling critical load of slender struts subjected to compression.The unit allows to study the buckling of pieces of different lengths, ranging from 300 mm. to 625 mm.,...
EULER BUCKLING MODES UNIT - MEBM
  • MEBM
Available
7.3.2.1.- UJI MEKANIK
MEBM
Euler Buckling Modes Unit
With the Euler Buckling Modes Unit, "MEBM", the four Euler buckling cases are demonstrated, for which four elastic bars are fixed or supported in a frame and subjected to compression load with a system of weights.The elastic bars can be free or...
TORSION AND BEND UNIT - MTP
  • MTP
Available
7.3.2.1.- UJI MEKANIK
MTP
Unit Putar dan Tekuk
The Torsion and Bend Unit, "MTP", is a combined apparatus for the demonstration of both torsion and bend to be used in the laboratory or as a complement of the theoretical study about torsion and bend. Its size and weight facilitate its transport...
TORSION UNIT - MTB
  • MTB
Available
7.3.2.1.- UJI MEKANIK
MTB
Unit Torsi
The Torsion Unit, "MTB", allows to verify the basis of torsion and to perform practical exercises to demonstrate:Circular rods elastic torsion equation.The rigidity modulus of different materials.To perform the tests a metallic rod is fastened by...
TORSION TEST UNIT (30NM) - MTT
  • MTT
Available
7.3.2.1.- UJI MEKANIK
MTT
Torsion Test Unit (30Nm)
To perform the tests, the test specimen is clamped and twisted by means of a flywheel and a worm gear until it breaks. The force is gradually applied to the specimen to observe the elastic strain produced. The specimen will deform and manifest...
TENSILE TESTER UNIT - MTTU
  • MTTU
Available
7.3.2.1.- UJI MEKANIK
MTTU
Tensile Tester Unit
With the Tensile Tester Unit, "MTTU", tensile test can be performed. A specimen made of different materials is subjected to an increasing axial tensile stress till failure. This unit allows the user to perform tensile tests with different...
DEFLECTION OF CURVED BARS UNIT - MDB
  • MDB
Available
7.3.2.1.- UJI MEKANIK
MDB
Unit Kelendutan Batang Melengkung
The Deflection of Curved Bars Unit "MDB" consists of a structure of aluminum and steel that allows the incorporation of different curved bars to be studied. It allows tests with curved bars of different shape.The use of two dial gauges placed...
BEAM DEFLECTION UNIT - MFV
  • MFV
Available
7.3.2.1.- UJI MEKANIK
MFV
Unit Beam Deflection
The Beam Deflection Unit, "MFV" has been designed to enable the students to observe and study the following phenomena in simply supported beams and cantilever beams:Relation between the deflections and the applied loads.Effect of the length and...
SHEAR FORCE AND BENDING MOMENTUM UNIT - MMF
  • MMF
Available
7.3.2.1.- UJI MEKANIK
MMF
Unit Pembagian Kekuatan dan Momen Tekuk
The Shear Force and Bending Momentum Unit, "MMF", unit is formed by an aluminum and steel structure that allows us to perform a mechanical study of different structures.An articulated structure makes it possible to convert the application of one...
COMPUTER CONTROLLED NOISE CONTROL DEMONSTRATION UNIT - TDRC
  • TDRC
Available
7.3.2.2.- UJI TERMAL DAN AKUSTIK
TDRC
Computer Controlled Noise Control Demonstration Unit
The Computer Controlled Noise Control Demonstration Unit, "TDRC", has been specifically designed to obtain visual and quantitative results related to noise and vibration control.The main parts of the unit are two noise sources consisting of a...
BELL CASTING BASIC TRAINING SET - MCAM
  • MCAM
Available
7.3.3.1.- PENDANAAN
MCAM
Bell Casting Basic Training Set
Didactic case for the study of foundry fundamentals.Introduction to sand casting: student experiments with three different patterns (bell, anvil and anchor).Operations of ramming up of the moulding sand, melting of the metal, pouring, forming and...
FOUNDRY, BUILDING-UP TRAINING SET 1 - MCLA
  • MCLA
Available
7.3.3.1.- PENDANAAN
MCLA
Foundry, Building-up Training Set 1
Didactic case for the study of foundry fundamentals.Operations of ramming up of the moulding sand, melting of the metal, pouring, forming and fettling can be performed step by step.Practice of melting, unmelting and foundry with irregular and...
CENTRIFUGAL CASTING, BUILDING-UP TRAINING SET 2 - MCEN
  • MCEN
Available
7.3.3.1.- PENDANAAN
MCEN
Centrifugal Casting, Building-up Training Set 2
This unit is designed for production of hollow bodies in a fast rotating die.The unit is mounted on a thick steel sheet and hold by a frame of extruded and anodised aluminium, which provides a great stiffness and resistance.This unit is made up of...
Meminta informasi