Terlaris

Menampilkan 745 -768 dari 950 produk

BRINELL, VICKERS & ROCKWELL HARDNESS TESTING UNIT - EBVR

EBVR

Available

7.3.2.1.- UJI MEKANIK

EBVR

Peralatan Uji Kekerasan "Brinell", "Vickers" dan "Rockwell"

The Brinell, Vickers and Rockwell Hardness Testing Unit, "EBVR", designed by EDIBON, consists of a hardness testing machine that determines the three main types of hardness (Brinell, Vickers and Rockwell). It can be adapted to determine hardness...

Available

7.3.2.1.- UJI MEKANIK

EEF

Peralatan Uji Kelelahan

The Fatigue Testing Unit, "EEF", designed by EDIBON, allows to study the fatigue strength of the materials. For that purpose, fatigue tests are performed with different materials and notches.Optionally, with the additional recommended element Set...

COMPUTER CONTROLLED FATIGUE TESTING UNIT - EEFC

EEFC

Available

7.3.2.1.- UJI MEKANIK

EEFC

Peralatan Uji Kelelahan, Dikendalikan dari Komputer (PC)

The Computer Controlled Fatigue Testing Unit, "EEFC", designed by EDIBON, allows to study the fatigue strength of the materials. For that purpose, fatigue tests are performed with different materials and notches.Optionally, with the additional...

COMPUTER CONTROLLED TWO-STAGE COMPRESSOR TEST UNIT - HCDEC

HCDEC

Available

8.7.5.- KOMPRESOR

HCDEC

Peralatan Uji Kompresor Dua Tahap, Dikendalikan dari Komputer (PC)

The Computer Controlled Two-Stage Compressor Test Unit, "HCDEC", works with compressed air and presents as a principal device a compression bench with two pistons, low and high pressure.This unit presents four circuits or work dispositions which...

UNIVERSAL MATERIAL TESTING UNIT - EEU/20KN

EEU/20KN

Available

7.3.2.1.- UJI MEKANIK

EEU/20KN

Peralatan Uji Material Universal

The Universal Material Testing Unit, "EEU/20KN", designed by EDIBON, is a didactic bench-top universal material testing unit. It is distinguished by its rigid construction, accurate control and a precise hydraulic system to apply loads of up to 20...

MTTU

Available

7.3.2.1.- UJI MEKANIK

MTTU

Peralatan Uji Tarik

With the Tensile Tester Unit, "MTTU", designed by EDIBON, tensile test can be performed. A specimen made of different materials is subjected to an increasing axial tensile stress till failure. This unit allows the user to perform tensile tests...

Available

7.3.2.1.- UJI MEKANIK

MTT

Peralatan Uji Torsi (30Nm)

The Torsion Test Unit (30Nm), "MTT", designed by EDIBON, has a shaft attached to the test specimen where the moment of torsion is measured with strain gauges. By means of an angle measuring sensor it is possible to determine the torsion angle....

COMPUTER CONTROLLED BIOMEDICAL ULTRASOUND THERMAL EFFECTS TEACHING UNIT - BIUTEC

BIUTEC

Available

14.3.- PERALATAN BIOMEDIS

BIUTEC

Peralatan Ultrasonografi dalam Biomedis, Dikendalikan dari Komputer (PC)

The Computer Controlled Biomedical Ultrasound Thermal Effects Teaching Unit, "BIUTEC", has been designed by EDIBON to study, in an experimental way, the ultrasound effects in biological tissues and acquire the necessary knowledge to design and...

Available

7.3.2.1.- UJI MEKANIK

MUP

Peralatan Universal untuk Tekuk

The Universal Buckling Unit "MUP" is a bench-top unit whose frame is made of anodized aluminum profiles and plates and steel elements, on which a bubble level is installed to equilibrate the system.The unit has been designed to carry out tests...

CORIOLIS FORCE DEMONSTRATION UNIT - MDFC

MDFC

Available

7.1.3.- STATICS AND DYNAMICS

MDFC

Peralatan untuk Demonstrasi Gaya Coriolis

The Coriolis Force Demonstration Unit, "MDFC", designed by EDIBON, is used to observe the deflection of a jet of water generated by a pump attached to a rotating arm that rotates to different speeds in a horizontal plane. An electronically...

COMPUTER CONTROLLED CRITICAL SPEED INVESTIGATION UNIT - MVCC

MVCC

Available

7.1.4.- GETARAN DAN OSILASI

MVCC

Peralatan untuk Penelitian Kecepatan Kritis, Dikendalikan dari Komputer (PC)

Some phenomena that appear in mechanical systems, such as vibration, self-centering and resonance in rotary shafts, can be clearly demonstrated with the Computer Controlled Critical Speed Investigation Unit, "MVCC".The operation of the "MVCC" unit...

UNIT FOR DETERMINING THE GAUGE FACTOR OF STRAIN GAUGES - MFGE

MFGE

Available

7.3.1.- FOTOELASTISITAS DAN PENGUKURAN STRAIN

MFGE

Peralatan untuk Penentuan Faktor Strain Gauge

The Unit for Determining the Gauge Factor of Strain Gauges, "MFGE", designed by EDIBON, allows to determine the k factor of strain gauges.The bar rests on two supports with ball bearings, so that it is possible to work with a load under pure...

CECI

Available

6.1.1.2.- PENGONTROL INDUSTRI

CECI

Peralatan untuk Pengendali Industri

The Industrial Controllers Unit, "CECI", is based on a modular design structure whose functionality is divided into different modules toallow the student a better understanding of the unit. The modules included in the unit are: industrial...

MSCT

Available

7.4.3.- PRAKTIK INSTALASI DAN PEMELIHARAAN

MSCT

Peralatan untuk Pengujian Sambungan Berulir

The Screw Joint Testing Unit, "MSCT", represents the simulation of a tightening set consisting of a screw and a nut on two rectangular shaped beams.A very precise torque wrench performs the tightening through a threaded rod and a flywheel. The...

COMPUTER CONTROLLED UNIT TO STUDY FLOW THROUGH PACKED COLUMNS - FPCC

FPCC

Available

11.1.8.- PENYERAPAN DAN ADSORPSI

FPCC

Peralatan untuk Studi Aliran dalam Kolom Pengisi, Dikendalikan dari Komputer (PC)

The Computer Controlled Unit to Study Flow through Packed Columns, "FPCC", designed by EDIBON, unit is a transparent packed column, which can be used with water, air or both fluids, simulating an absorption column.When working with water, the unit...

HECA

Available

8.8.- SISTEM PIPA FLUIDA

HECA

Peralatan untuk Studi Aliran Udara

The Air Flow Studies Unit, "HECA", designed by EDIBON, is a floor standing unit that allows to measure different characteristics of air distribution systems and to demonstrate certain basic principles of fluid mechanics in ducts and jets.The unit...

UNIT FOR STUDYING DEFORMATION OF TRUSSES - MFCS3

MFCS3

Available

7.1.6.- MEKANIKA STRUKTURAL

MFCS3

Peralatan untuk Studi Deformasi pada Rangka

The Unit for studying Deformation of Trusses, "MFCS3", designed by EDIBON, allows the measurement of the stresses in the bars in different types of trusses, and the study of the dependence of the external force and the comparison of the...

COMPUTER CONTROLLED TEACHING UNIT FOR THE STUDY OF POWER ELECTRONICS (WITH IGBTS) - TECNEL

TECNEL

Available

6.1.2.2.- ELEKTRONIK TENAGA DAN ELEKTRONIK INDUSTRI

TECNEL

Peralatan untuk Studi Elektronika Daya (dengan IGBT), Dikendalikan dari Komputer (PC)

The Computer Controlled Teaching Unit for the Study of Power Electronics (with IGBTS). (Converters: AC/AC+AC/DC+DC/DC+AC/ AC), "TECNEL", designed by EDIBON, is a unit with Computer Control and Data Acquisition System designed to study the basis of...

UNIT FOR STUDYING FORCES IN A SIMPLE BAR STRUCTURE - MFBS

MFBS

Available

7.1.6.- MEKANIKA STRUKTURAL

MFBS

Peralatan untuk Studi Gaya pada Struktur Batang Sederhana (Rangka Sederhana)

The Unit for Studying Forces in a Simple Bar Structure, "MFBS", designed by EDIBON allows the study of forces acting on a simple truss when is subjected to a point load in one of the nodes that make up the structure.It consists of a group of five...

MFCE

Available

7.1.3.- STATICS AND DYNAMICS

MFCE

Peralatan untuk Studi Gaya Sentrifugal

The Centrifugal Force Unit, "MFCE", designed by EDIBON, is used to demonstrate the relationship between centrifugal force, rotational speed, mass of a rotating body and distance from the axis.The unit consists of a vertical axis of rotation and a...

UNIT FOR STUDYING BEARING FRICTION - MBF

Available

7.1.5.- TRIBOLOGY (FRICTION, WEAR, LUBRICATION)

MBF

Peralatan untuk Studi Gesekan pada Bantalan

The Unit for Studying Bearing Friction, "MBF", has been designed by EDIBON to study sliding friction in slide bearings and rolling bearings. Since rolling friction is very little, rotational dynamics basic tests can be performed with the inertia...

MELH

Available

7.1.3.- STATICS AND DYNAMICS

MELH

Peralatan untuk Studi Hukum Hooke

The Unit for studying Hooke's Law, "MELH", designed by EDIBON, demonstrates the application of Hooke's Law and allows the visualization of the deformation of tension springs under load and the performance of oscillation experiments on a spring –...

UNIT TO STUDY THE PRESSURE DROP OF COMPRESSIBLE FLUIDS IN PIPES - PDCFP

PDCFP

Available

8.8.- SISTEM PIPA FLUIDA

PDCFP

Peralatan untuk Studi Kehilangan Tekanan pada Fluida Kompresibel di Pipa

The Unit to Study the Pressure Drop of Compressible Fluids in Pipes, "PDCFP", allows the study of the compressible fluid pressure drop, for example the air of a compressor, and the different flow conditions (laminar and turbulent) thanks to the...

UNIT FOR STUDYING EQUILIBRIUM OF MOMENTS ON A TWO ARM LEVER - MEMB2

MEMB2

Available

7.1.3.- STATICS AND DYNAMICS

MEMB2

Peralatan untuk Studi Keseimbangan Momen pada Tuas Dua Lengan

The Unit for studying Equilibrium of Moments on a Two Arm Lever, "MEMB2", has been designed by EDIBON to study the fundamentals of the equilibrium of moments and the application of the law of levers on a two-arm lever.A pivoted beam in the extreme...

UNTUK INFORMASI LEBIH LANJUT, HUBUNGI KAMI