AEL-KNX-BC Aplikasi Pelatihan Kontrol Tirai dengan KNX

KNX BLIND CONTROL TRAINING APPLICATION - AEL-KNX-BC

SISTEM INOVATIF

The AEL-KNX-BC is an application designed to facilitate the study and understanding of KNX based blind control systems. This unit serves as a valuable resource for educational and professional purposes, providing hands-on experience and knowledge of the wiring, programming and commissioning techniques associated with KNX technology in the context of blind control systems.

Lihat uraian umum

BERITA TERKAIT

GAMBARAN UMUM

The AEL-KNX-BC is an application designed to facilitate the study and understanding of KNX based blind control systems. This unit serves as a valuable resource for educational and professional purposes, providing hands-on experience and knowledge of the wiring, programming and commissioning techniques associated with KNX technology in the context of blind control systems.

Key features of the AEL-KNX-BC include:

  • Hands-on Learning: the unit allows users to perform practical exercises related to KNX wiring practices, focusing on the specific requirements of shutter or blind control scenarios.
  • Simulation of Blind Control Scenarios: Users can simulate and experiment with various scenarios related to blind control, gaining an understanding of how KNX technology facilitates the integration and automation of such systems in intelligent buildings.
  • Practical application of KNX wiring: The unit provides a platform for practical application, allowing users to connect and configure KNX devices for blind control in a controlled environment. This hands-on approach enhances the learning experience.
  • Comprehensive documentation: The accompanying documentation provides detailed information on KNX wiring practices for blind control, ensuring that users have access to comprehensive guidance and instructions for effective learning.
  • Compatibility: Compatible with standard KNX devices and protocols used in blind control systems, ensuring seamless integration into KNX-based educational and professional environments.

LATIHAN DAN PRAKTEK PEDOMAN

LATIHAN PRAKTIS YANG DIANDAL TERMASUK DALAM PANDUAN

  1. Basic Integration of the Blind Control System: connection of the power supply for the KNX devices in the blind control system.
  2. Connection of the KNX Room Controller: integration of the KNX room controller for centralized blind control and configuration of functions and scenario programming.
  3. Connection of KNX Binary Output Module for Shutter Control: connection and configuration of the KNX binary output module for effective shutter control. Adjustment of response times and configuration of positions.
  4. Use of KNX Brightness Sensors: connection and integration of KNX brightness sensors for automatic adjustment of blinds according to lighting. Programming of thresholds and conditions.
  5. Connection of Pushbutton Modules for Manual Interaction: integration of KNX pushbutton modules to allow manual interaction with the blinds. Programming of up, down and stop functions.
  6. Shutter Motor: Connection and Integration: Connection and programming of the shutter motor.

Project creation in ETS and Topology definition:

  1. Creation of a New Project in ETS: development of a new project from scratch with the ETS software and definition of general characteristics and establishment of the basic topology of the KNX system.
  2. Bus Topology Definition: configuration of the KNX bus topology, identification of devices and establishment of physical addresses.
  3. Physical Address Assignment: assignment of physical addresses to KNX devices in the project and following of addressing standards and recommendations.
  4. Topology Verification: verification of configuration consistency and compliance with KNX system requirements.

KNX Device Diagnostics:

  1. Use of Diagnostic Tools: use of diagnostic tools in the ETS software to verify communication and status of KNX devices.
  2. Communication Testing: performing communication tests between KNX devices and the bus and identification and resolution of possible connection problems.
  3. Telegram Analysis: analysis of telegrams sent and received by KNX devices, identification of possible errors or interferences in the network.
  4. Troubleshooting: diagnosis and resolution of configuration or connection errors in KNX devices and use of diagnostic tools available in the ETS software.
  5. Event Logging: use of event logging functions to monitor and analyze the behavior of KNX devices under different operating conditions.

KUALITAS

LAYANAN PURNA JUAL

Meminta informasi