The objective of the Anaerobic Digester, "PDAN", is to study and understand the stages of the anaerobic digestion, as well as the anaerobic digestion process itself. It is supplied with two packed anaerobic digesters. In this way, the user can...

The objective of the Computer Controlled Anaerobic Digester, "PDANC", is to study and understand the stages of the anaerobic digestion, as well as the anaerobic digestion process itself. It is supplied with two packed anaerobic digesters. In this...

The objective of the Computer Controlled Aerobic Digester, "PDAC", unit is to study and understand aerobic digestion processes and to analyze their main parameters. The unit consists of a 20 l capacity reactor vessel with a tubular membrane made...

The Antenna Unit, "EAN", is a complete and affordable unit and no extra hardware is required for complete all the practice set.The "EAN" allows students to learn how to perform the essential antenna measurements: radiation pattern with the measure...

The Flow Visualization Aerodynamic Tunnel, "TAVF180/100", consists of a vertical conduction in which an upward flow of air and smoke is induced, which passes through different models allowing to study the behavior of the flow around it. Thus it is...

The Aerodynamic Tunnel, 50 x 250 mm, "TA50/250", is a wind tunnel designed to study subsonic aerodynamics in a tunnel in open circuit and with incompressible subsonic flow. Air is drawn by a variable speed fan located at the discharge end of the...

The Computer Controlled Aerodynamic Tunnel, 50 x 250 mm, "TA50/250C", is a wind tunnel designed to study subsonic aerodynamics in a tunnel in open circuit and with incompressible subsonic flow. Air is drawn by a variable speed fan, computer...

The Aerodynamic Tunnel, 300 x 300 mm, "TA300/300", is a wind tunnel designed to study subsonic aerodynamics in a tunnel in open circuit and with incompressible subsonic flow. Air is drawn by a variable speed fan located at the discharge end of the...

The Computer Controlled Aerodynamic Tunnel, 300 x 300 mm, "TA300/300C", is a wind tunnel designed to study subsonic aerodynamics in a tunnel in open circuit and with incompressible subsonic flow. Air is drawn by a variable speed fan, computer...

Aerodynamics is the part of fluid mechanics that studies the motion of gases and the forces or reactions to which the bodies they interact with are subjected. Aerodynamics is not only important by itself but also as a complement to aeronautics....

The BSUB is a complete unit designed to provide signal conditioning for many sensors and transducers output signals that must be conditioned. These circuits consist of differential and instrumentation amplifiers, filters, current to voltage and...

The BSPC is a complete unit designed to provide signal conditioning for many sensors and transducers output signals that must be conditioned before a data acquisition system can effectively and accurately acquire the signal. These circuits consist...

The Base Service Unit, "QRUBI", provides the necessary elements for the operation of the different reactor modules.It performs the following functions:Liquid reagent feeding: comprised of two 10-liter glass tanks, two dosing pumps with a capacity...

Hydraulics is the branch of science that deals with the mechanical properties of fluids, and Fluid Mechanics provides the foundation for hydraulics.With LIFLUBA (Basic Fluids Mechanics Integrated Laboratory), EDIBON tries to give answer to the...

This unit is common for Heat Exchangers type "TI" and can work with one or several exchangers.This unit performs the following tasks:Heating water in a computer controlled thermostatic bath.Pumping the hot water.Regulation and measurement of the...

The Basic Hydraulic Feed System, "FME00/B", designed by EDIBON is a service unit for different Fluid Mechanics Units as: "FME" type modules, Fluid Friction in Pipes Unit "AFT", etc., increasing the equipment profitability.

BDAS is designed to monitor the measurements of each unit type "FME" from a computer (PC).This system can monitor any unit, checking the revolutions given by the water pump or the torque, differential pressures for Bernoulli theorems, pressure...

This unit is self-complete, it includes hardware, power supply and the necessary connections for supplying power and allocating the available modules.

The Computer Controlled Wind Energy Basic Unit, "MINI-EEEC", is a small-scale unit designed to study wind energy and the influence of some factors on its generation.This unit consists of a transparent tunnel, a wind turbine with rotor to place up...

The Computer Controlled Basic Teaching Unit for the Study of Power Electronics (no IGBTS). (Converters: AC/DC+AC/AC), "TECNEL/B", is a unit with Computer Control and Data Acquisition System designed to study the basis of Power Electronics. It...

The Basic Teaching Unit for the Study of Regulation and Control, "RYC/B", allows the user to learn the basics about regulation and control of first and second order systems.This unit enables to carry a set of practices related with basic...

The Wind Energy Basic Unit, "MINI-EEE", is a small-scale unit designed to study wind energy and the influence of some factors on its generation.This unit consists of a transparent tunnel, a wind turbine with rotor to place up to six blades and a...

"SERIN/CCB" is an unit whose goal is studying low power servo systems. It is a low power DC motor speed control trainer that has a breakdown simulator. This trainer is a basic version of the Advanced and Computerised "SERIN/CC" Trainer, being...

The Computer Controlled Thermal Solar Energy Basic Unit, "MINI-EESTC", allows to demonstrate solar thermal heating of domestic water in an illustrative manner.This unit is a system that transforms solar energy into usable thermal energy. It uses...

This unit is a system that transforms solar energy into usable thermal energy.This unit uses the thermosiphon system to heat water or the traditional pumping system. In both cases, the absorbed thermal energy is given by the simulated solar...

The Basic Pipe Network Unit, "FME23", designed by EDIBON, allows the study of pressures and flows created by interconnected pipes, i.e. in a network.The objective of this unit is to simulate the problems that could originate in pipe networks, with...

The Computer Controlled Basic Heat Exchangers Unit (TICC/SS) has been designed by Edibon to study and compare different types of small-scale heat exchangers working with parallel or counterflow arrangements.The complete unit consists of two main...

The Basic Unit of Mechanical Drive Systems, "MDSU", consists of a main frame where a series of accessories and elements are arranged, distributed in modules of different level, thought to introduce the user in the field of mechanical systems and...