NEW Basic Mechanics course
Читать дальше7.1.- МАШИНОСТРОЕНИЕ
Механическая инженерия - это применение физики к элементам, которые нас окружают, для улучшения существующих механических устройств или создания новых. Поскольку он основан на физических принципах, его происхождение восходит к истокам этих принципов, и его разработка тесно связана с достижениями механики. Тем не менее, только изобретение парового двигателя стало одним из столпов развития отрасли.
Узнать большеВ результате создания этого устройства произошла Промышленная революция семнадцатого века. С этого момента при участии ученых и инженеров, столь же важных, как Ватт, Стефенсон, Тесла или Ранкин, началось беспрецедентное обновление как концепции, так и разработки новых аппаратов.
Понятие промышленности, как оно было известно до этого момента, изменилось с развитием этих машин. Масовое производство было реализовано, машинныедизайны были усовершенствованы, и, следовательно, расширился диапазон производственных процессов, в результате чего появилось немыслимое разнообразие новых продуктов, адаптированных к потребностям общества.
С точки зрения машиностроения, стоит упомянуть следующие области изучения и применения:
- Механизмы.
- Структуры.
- Динамика.
- Вибрации.
- Обстановки.
В настоящее время любая отрасль промышленности, от продовольственной до аэрокосмической, должна быть на самом высоком технологическом уровне инновации. Поэтому исследования и разработки новых устройств особенно важны для того, чтобы всегда иметь новейшую технологию и быть на уровне, требуемом отраслью 4.0.
Посмотреть продукты
Материалы по Tеме
ПРОДУКТЫ МАШИНОСТРОЕНИЕ
7.1.3.- СТАТИКА И ДИНАМИКА
CGU
The Centrifugal Governor Unit, "CGU", has been designed to study the operating mode of different centrifugal governors, including three interchangeable governors: Porter governor, Hartnell governor and Proell governor.Interchangeable governors...
7.1.3.- СТАТИКА И ДИНАМИКА
MED
Установка для балансировки статики и динамики
The Static and Dynamic Balancing Unit, "MED", developed by EDIBON is a unit to study and analyze the oscillations and vibrations and how to eliminate or diminish them.Basically, the unit is formed by a shaft mounted on bearings. The shaft is...
7.1.3.- СТАТИКА И ДИНАМИКА
MES
Установка простой балансировки
The Simple Balancing Unit, "MES", developed by EDIBON is a unit to study and analyze the oscillations and vibrations and how to eliminate or diminish them.Basically, the unit is formed by a shaft mounted on bearings. The shaft is coupled by pulley...
7.1.3.- СТАТИКА И ДИНАМИКА
MIF
Устройство инерционного маховика
The Inertia Flywheel Unit, "MIF", consists of an inertia disc with a rotation shaft at the center of the disc.The shaft is supported at two points by bearings.A cord is attached by one of the ends to the shaft and wound around it. At the other end...
7.1.3.- СТАТИКА И ДИНАМИКА
MRYE1
Устройство для вращения колёс и осей
The Wheel and Axle Unit, "MRYE1", is a unit which allows to investigate the mechanics of a simple wheel and axle machine and to demonstrate the laws of the formation of equilibrium of moments in static systems.Two pulleys with different diameter...
7.1.3.- СТАТИКА И ДИНАМИКА
MRYE2
Устройство для вращения колёс и дифференциальных осей
The Wheel and Differential Axle Unit, "MRYE2", is a unit that allows for investigating the mechanics of a wheel and differential axle mechanism and demonstrating the force reduction on a differential pulley block.A wheel, consisting of a pulley...
7.1.3.- СТАТИКА И ДИНАМИКА
MELH
Устройство для изучения законa Гука
The Unit for studying Hooke's Law, "MELH", demonstrates the application of Hooke's Law and allows the visualization of the deformation of tension springs under load and the performance of oscillation experiments on a spring – mass system.The...
7.1.3.- СТАТИКА И ДИНАМИКА
MSHU
Устройство простых гармонических колебаний
This Simple Harmonic Motion Unit, "MSHU", allows many experiments using several pendulums and devices, such as different types of pendulums (simple, bifilar, trifilar and Kater’s pendulum) and springs.Consists of a panel with a support that allows...
7.1.3.- СТАТИКА И ДИНАМИКА
SRI
Устройство для изучения инерции вращения
The Unit to Study Rotational Inertia, "SRI", has been designed to carry out tests to analyze the moments of inertia of a solid and a hollow cylinder, both with same mass and diameter. The moment of inertia of another hollow cylinder with different...
7.1.4.- ВИБРАЦИЯ И КОЛЕБАНИЯ
MEVTC
Контролируемое ПК устройство для изучения колебаний при кручении
The Computer Controlled Torsional Vibration Unit, "MEVTC" is designed to study torsion suffered by some shafts with rotation motion, apart from studying the torsional rigidity and the behavior of a torsional vibration system with one, two or three...
7.1.4.- ВИБРАЦИЯ И КОЛЕБАНИЯ
MVRE
Вибрации спирального вытянутого элемента
The Vibration of Coil Spring Unit, "MVRE", unit has been designed to study and understand a coil torsion spring, a mass-spring system and the fundamental properties of its characteristic periodic motion. In this sense, the unit consists of a rigid...
7.1.4.- ВИБРАЦИЯ И КОЛЕБАНИЯ
MVL
Безвибрационное устройство
The Free Vibration Unit, "MVL", has been developed to cover a range of demonstrations and experiments which provide the user with an understanding of the free vibrations of a simple spring-mass-damper system. Simple adjustments can be made to the...
7.1.4.- ВИБРАЦИЯ И КОЛЕБАНИЯ
MVLF
Установка простых и вынужденых вибраций
The Free and Forced Vibration Unit, "MVLF", has been developed to cover a range of demonstrations and experiments which provide the user with an understanding of the free and forced vibrations of a simple spring-mass-damper system. Simple...
7.1.4.- ВИБРАЦИЯ И КОЛЕБАНИЯ
MEVLB
Устройство для изучения свободных вибраций стержня
The Unit for Studying Free Vibration of a Bar,"MEVLB", allows to study the features of the free vibrations of a bending bar.The natural frequency of the bending bar can be modified adding additional loads at the free end of a bar or varying the...
7.1.4.- ВИБРАЦИЯ И КОЛЕБАНИЯ
MOT
Установка крутильных колебаний
The Torsional Oscillations Unit, "MOT", is intended for easy experiments. It enables to illustrate and investigate the torsional oscillation in single rotor, multi-rotor and geared systems. The unit basically consists of a rigid frame that have...
7.1.4.- ВИБРАЦИЯ И КОЛЕБАНИЯ
MVCC
Управляемое ПК устройство изучения критической скорости
Some phenomena that appear in mechanical systems, such as vibration, self-centering and resonance in rotary shafts, can be clearly demonstrated with the Computer Controlled Critical Speed Investigation Unit, "MVCC". The operation of the "MVCC"...
7.1.4.- ВИБРАЦИЯ И КОЛЕБАНИЯ
MEER
Установка для вращения валов
The Whirling of Shafts Unit, "MEER", has been designed by EDIBON to demonstrate and determine different modes of oscillation and resonance of shafts with continuous distribution of mass under different conditions.The operation of the Whirling of...
7.1.5.- ТРИБОЛОГИЯ (ТРЕНИЕ, ИЗНОС, СМАЗКА)
MCF
Установка трения в ремённой передаче
The Belt Friction Unit, "MCF", allows us to carry out studies and investigations to compare the driving torque for a given degree of overlap of a flat belt (leather or rope) and a V belt.With this unit the relationship between the tensions in the...
7.1.5.- ТРИБОЛОГИЯ (ТРЕНИЕ, ИЗНОС, СМАЗКА)
MEF
Установка для изучения трения
The Friction Study Unit, "MEF", allows the unit to illustrate the friction force by simple demonstrations.It is designed for the study of the relations between friction forces and normal forces, between hard or soft surfaces, between lubricated or...
7.1.5.- ТРИБОЛОГИЯ (ТРЕНИЕ, ИЗНОС, СМАЗКА)
MPCO
Установка для опорных подшипников
The Journal Bearing Unit, "MPCO", allows to study the pressure distribution in sliding bearings. It illustrates the principle of hydrodynamic lubrication.The unit is mounted on a metallic structure assembled on wheels for its mobility.The sliding...
7.1.5.- ТРИБОЛОГИЯ (ТРЕНИЕ, ИЗНОС, СМАЗКА)
MEMT
Модульный тренажёр по трибологии
The Tribology Modular Unit, "MEMT", consists of a base unit with electronic console and a series of experimental units to investigate and visualize tribological phenomena.MEMT-UB. Drive Unit for Tribological Tests. This unit is common for the...
7.1.5.- ТРИБОЛОГИЯ (ТРЕНИЕ, ИЗНОС, СМАЗКА)
MEMT-UB
Приводное устройство для трибологических тестов
Аксессуар
MEMT
This unit is common for the modules type "MEMT". It consists of a base unit and an electronic console:The Base Unit consists of a drive unit formed by a DC motor with a shaft. The motor is mounted in a reduction gear, obtaining enough torque in...
7.1.5.- ТРИБОЛОГИЯ (ТРЕНИЕ, ИЗНОС, СМАЗКА)
MEMT-1
Модуль Распределения Давления во Втулке
Аксессуар
MEMT
This unit allows the visualization of the radial pressure distribution in a journal bearing with hydrodynamic lubrication.The "MEMT-1" unit consists of a journal bearing with hydrodynamic lubrication, a freely moving bearing housing with thirteen...
7.1.5.- ТРИБОЛОГИЯ (ТРЕНИЕ, ИЗНОС, СМАЗКА)
MEMT-2
Модуль Фрикционного Блока
Аксессуар
MEMT
This unit allows to demonstrate the friction forces between several cylinders of different materials and a roller under different lubrication conditions.The "MEMT-2" unit consists of two levers that transmit a force applied by weights to a test...
7.1.5.- ТРИБОЛОГИЯ (ТРЕНИЕ, ИЗНОС, СМАЗКА)
MEMT-3
Модуль Стержень-Диск
Аксессуар
MEMT
This unit allows to study the friction forces between several vertical friction pins of different materials and a rotating friction disc.The end of each vertical pin is made of a different material and rubs against the rotating steel disc. The...
7.1.5.- ТРИБОЛОГИЯ (ТРЕНИЕ, ИЗНОС, СМАЗКА)
MEMT-4
Модуль Пластины Прокатки
Аксессуар
MEMT
This module allows to determine the slip forces between two rotating friction discs in contact.The slip between the discs is maintained constant by a gearbox. The pressure can be adjusted with a lever and a set of weights. The unit includes a...
7.1.5.- ТРИБОЛОГИЯ (ТРЕНИЕ, ИЗНОС, СМАЗКА)
MEMT-5
Модуль Оптической Эластогидродинамики
Аксессуар
MEMT
This unit allows to investigate the thickness and characteristics of a lubricant film on a rolling sphere.The unit consists in a steel sphere and a driven glass disc.The sphere is pressed against the underside of the glass disc. The light from a...
7.1.5.- ТРИБОЛОГИЯ (ТРЕНИЕ, ИЗНОС, СМАЗКА)
MEMT-6
Модуль Фрикционных Автоколебаний с Периодическими Остановками
Аксессуар
MEMT
This module allows to demonstrate the static friction, the sliding friction, the related friction vibrations and the slip-stick effects.Several weights are placed on a horizontally rotating friction disc. It is prevented from turning by a cord....
7.1.5.- ТРИБОЛОГИЯ (ТРЕНИЕ, ИЗНОС, СМАЗКА)
MCD
Устройство тонкого цилиндра
The Thin Cylinder Unit, "MCD", has been developed to enable the student to verify various analytical formulae with actual measured results. Strain gauges mounted in various positions and orientations on the cylinder provide an opportunity for...
7.1.5.- ТРИБОЛОГИЯ (ТРЕНИЕ, ИЗНОС, СМАЗКА)
MBF
Устройство для изучения трения в подшипниках
The Unit for Studying Bearing Friction, "MBF", has been designed by EDIBON to study sliding friction in slide bearings and rolling bearings. Since rolling friction is very little, rotational dynamics basic tests can be performed with the inertia...
7.1.5.- ТРИБОЛОГИЯ (ТРЕНИЕ, ИЗНОС, СМАЗКА)
MCF/A
Установка трения ремня с динамометрами
The Belt Friction Unit with Dynamometers, "MCF/A", allows studies and investigations to compare the friction coefficient for a given contact angle of a flat belt and a V-belt.With this unit it is possible to observe the relationship between...
7.1.6.- СТРОИТЕЛЬНАЯ МЕХАНИКА
MCPG
Установка олстостенного цилиндра
In the Thick-Walled Cylinder Unit, "MCPG", the stresses are determined through the measurement of the strains produced on the surface. These strains are measured by strain gauges.The thick-walled vessel consists of an aluminum cylinder of length...
7.1.6.- СТРОИТЕЛЬНАЯ МЕХАНИКА
MFPG
Устройство для изучения распределения сил в консольном кране
The Unit for studying Forces in a Jib Crane, "MFPG", is designed to study the tensile and compressive forces in a planar central force system based on the example of a crane jib.The unit represents a planar central force system in which multiple...
7.1.6.- СТРОИТЕЛЬНАЯ МЕХАНИКА
MVS
Устройство висящего моста
The Suspension Bridge Unit, "MVS", consists of a deck and two parallel main cables that simulate a suspension bridge and allow the study of stress in the main cables. The deck of the bridge is simulated by a light alloy beam that is held by both...
7.1.6.- СТРОИТЕЛЬНАЯ МЕХАНИКА
MARP
Параболическая арка
The Parabolic Arch Unit "MARP" contains a pre-shaped articulated arch, which can be subjected to point or evenly distributed loads by means of seven uniformly distributed cables (cords) with hangers.One support of the arch is fixed whereas the...
7.1.6.- СТРОИТЕЛЬНАЯ МЕХАНИКА
MART
Трёхузловая арка
The Three-Hinged Arch Unit "MART" allows the student to become familiar with three-hinged arches, to calculate the bearing forces (for point load, for uniformly distributed load and for moving load), to investigate the influence of the load on the...