7.3.- 재료 공학

재료 공학은 재료 과학에 대한 산업적 해석을 수행하는 과학 산업 분야입니다. 인류 학적으로 인간 발달의 여러 단계는 도구 제조에 사용되는 재료 (석기 시대, 청동기 시대 등)에 따라 분류되었습니다. 따라서 인류의 발전은 신소재 연구와 밀접한 관련이 있습니다.

더보기

지난 200 년 동안 재료에 대한 발견은 재료의 특성과 구조 사이의 관계를 보여준 Gibbs의 공헌만큼 드러났습니다. 이를 통해 그래 핀과 같은 새로운 물질의 개발과 나노 물질 또는 나노 기술과 같은 새로운 분야의 연구가 가능해졌습니다.

이 정도의 개발에 도달하기 위해서는 굽힘, 경도 (Rockell, Brinell, Vickers, Martens), 비틀림, 견인력 (인성 및 탄력성), 장력 (크리프), 전단에 대한 기계적 테스트 모두 무한대의 테스트를 수행해야했습니다. , 화학 테스트 (열 처리, 내부 구조 등). 마찬가지로 다음과 같은 재료 분류가 이루어졌습니다.

  • 금속 (철 및 비철).
  • 세라믹.
  • 폴리머 (열가소성, 열경화성 및 엘라스토머).
  • 복합 재료.

이러한 발전의 응용은 자동차, 전자, 항공 우주, 항공, 생물 의학 등과 같은 다양한 산업 분야에서 드러나고 있으며, 따라서 오늘날 사회에서 재료 공학에 중요성을 부여합니다.

제품보기
관련 자료
재료 공학 UNITS
Showing 1-26 of 26 item(s)
COMPUTER CONTROLLED PHOTOELASTICITY UNIT - EFOC
  • EFOC
Available
14.1.7.- 광탄성 및 변형률 측정
EFOC

Computer Controlled Photoelasticity Unit

Unit for photoelasticity practices, illustrating the subjects of the Photoelasticity theory, the Elasticity theory, Strength of Materials, andStructure theory.It is very suitable for the introduction and study of photoelasticity: optical elements,...
PHOTOELASTICITY UNIT - EFO
  • EFO
Available
14.1.7.- 광탄성 및 변형률 측정
EFO

Photoelasticity Unit

Unit for photoelasticity practices, illustrating the subjects of the Photoelasticity theory, the Elasticity theory, Strength of Materials, and Structure theory. It is very suitable for the introduction and study of photoelasticity: optical...
STRAIN GAUGE TRAINING UNIT - MEGE
  • MEGE
Available
14.1.7.- 광탄성 및 변형률 측정
MEGE

Strain Gauge Training Unit

The Strain Gauge Training Unit (MEGE) provides an introduction to the fundamentals of measurement with strain gauges, to compare how resistance strain gauges work and how they measure strains in different structures (torsion, tension and bending...
UNIT FOR DETERMINING THE GAUGE FACTOR OF STRAIN GAUGES - MFGE
  • MFGE
Available
14.1.7.- 광탄성 및 변형률 측정
MFGE

Unit for Determining the Gauge Factor of Strain Gauges

The Unit for Determining the Gauge Factor of Strain Gauges, ,MFGE,, allows to determine the k factor of strain gauges. The bar rests on two supports with ball bearings, so that it is possible to work with a load under pure bending. To perform such...
UNIVERSAL MATERIAL TESTING UNIT - EEU/20KN
  • EEU/20KN
Available
7.3.2.1.- 기계적 테스트
EEU/20KN

Universal Material Testing Unit

The Universal Material Testing Unit, "EEU/20KN", is a didactic bench-top universal material testing unit. It is distinguished by its rigid construction, accurate control and a precise hydraulic system to apply loads of up to 20 kN, which enables...
BRINELL HARDNESS TESTING UNIT - EEDB
  • EEDB
Available
7.3.2.1.- 기계적 테스트
EEDB

Brinell Hardness Testing Unit

The Brinell Hardness Testing Unit, "EEDB", is a hardness tester that determines Brinell hardness in metals, hard alloys, tempered steels, etc. Besides, it can be used with other materials, such as rigid plastics, bakelite, etc.A penetrating ball...
BRINELL, VICKERS & ROCKWELL HARDNESS TESTING UNIT - EBVR
  • EBVR
Available
7.3.2.1.- 기계적 테스트
EBVR

Brinell, Vickers & Rockwell Hardness Testing Unit

The Brinell, Vickers and Rockwell Hardness Testing Unit, "EBVR", consists of a hardness testing machine that determines the three main types of hardness (Brinell, Vickers and Rockwell). It can be adapted to determine hardness of ferrous materials...
CREEP TESTING UNIT - EEFCR
  • EEFCR
Available
7.3.2.1.- 기계적 테스트
EEFCR

Creep Testing Unit

The Creep Testing Unit "EEFCR", for the creep testing is mounted on a structure of aluminum profiles which a painted steel panel is supported on.The EEFCR unit is designed to carry out experiments on specimens of plastic materials. Due to the...
COMPUTER CONTROLLED FATIGUE TESTING UNIT - EEFC
  • EEFC
Available
7.3.2.1.- 기계적 테스트
EEFC

Computer Controlled Fatigue Testing Unit

The Computer Controlled Fatigue Testing Unit, "EEFC", designed by EDIBON, allows to study the fatigue strength of the materials. For that purpose, fatigue tests are performed with different materials and notches.Optionally, with the additional...
FATIGUE TESTING UNIT - EEF
  • EEF
Available
7.3.2.1.- 기계적 테스트
EEF

Fatigue Testing Unit

The Fatigue Testing Unit, "EEF", designed by EDIBON, allows to study the fatigue strength of the materials. For that purpose, fatigue tests are performed with different materials and notches.Optionally, with the additional recommended element Set...
CHARPY AND IZOD IMPACT TESTING UNIT - EEICI
  • EEICI
Available
7.3.2.1.- 기계적 테스트
EEICI

Charpy and Izod Impact Testing Unit

The Charpy and Izod Impact Testing Unit "EEICI" consists of a pendulum supported on bearings with an arm of 330 mm long and a fastening system in the initial position of the test. The suitable hammer either for Charpy or Izod test is screwed to...
UNIVERSAL BUCKLING UNIT - MUP
  • MUP
Available
7.3.2.1.- 기계적 테스트
MUP

Universal Buckling Unit

The Universal Buckling Unit "MUP" is a bench-top unit whose frame is made of anodized aluminum profiles and plates and steel elements, on which a bubble level is installed to equilibrate the system.The unit has been designed to carry out tests...
STRUT BUCKLING UNIT - MFLT
  • MFLT
Available
7.3.2.1.- 기계적 테스트
MFLT

Strut Buckling Unit

The Strut Buckling Unit "MFLT" allows the student to obtain experimentally the buckling critical load of slender struts subjected to compression.The unit allows to study the buckling of pieces of different lengths, ranging from 300 mm. to 625 mm.,...
TORSION AND BEND UNIT - MTP
  • MTP
Available
7.3.2.1.- 기계적 테스트
MTP

Torsion and Bend Unit

The Torsion and Bend Unit, "MTP", is a combined apparatus for the demonstration of both torsion and bend to be used in the laboratory or as a complement of the theoretical study about torsion and bend. Its size and weight facilitate its transport...
TORSION UNIT - MTB
  • MTB
Available
7.3.2.1.- 기계적 테스트
MTB

Torsion Unit

To perform the tests a metallic rod is fastened by clamps and subjected to the testing force. Force is gradually applied on the rod to observe the elastic tension generated. The force moment or torque is applied by a dynamometer with a lever....
TENSILE TESTER UNIT - MTTU
  • MTTU
Available
7.3.2.1.- 기계적 테스트
MTTU

Tensile Tester Unit

With the Tensile Tester Unit, "MTTU", tensile test can be performed. A specimen made of different materials is subjected to an increasing axial tensile stress till failure. This unit allows the user to perform tensile tests with different...
DEFLECTION OF CURVED BARS UNIT - MDB
  • MDB
Available
7.3.2.1.- 기계적 테스트
MDB

Deflection of Curved Bars Unit

The Deflection of Curved Bars Unit "MDB" consists of a structure of aluminum and steel that allows the incorporation of different curved bars to be studied. It allows tests with curved bars of different shape.The use of two dial gauges placed...
BEAM DEFLECTION UNIT - MFV
  • MFV
Available
7.3.2.1.- 기계적 테스트
MFV

Beam Deflection Unit

The Beam Deflection Unit, "MFV" has been designed to enable the students to observe and study the following phenomena in simply supported beams and cantilever beams:Relation between the deflections and the applied loads.Effect of the length and...
SHEAR FORCE AND BENDING MOMENTUM UNIT - MMF
  • MMF
Available
7.3.2.1.- 기계적 테스트
MMF

Shear Force and Bending Momentum Unit

The Shear Force and Bending Momentum Unit, "MMF", unit is formed by an aluminum and steel structure that allows us to perform a mechanical study of different structures.An articulated structure makes it possible to convert the application of one...
BELL CASTING BASIC TRAINING SET - MCAM
  • MCAM
Available
7.3.3.1.- 주조
MCAM

Bell Casting Basic Training Set

Didactic case for the study of foundry fundamentals.Introduction to sand casting: student experiments with three different patterns (bell, anvil and anchor).Operations of ramming up of the moulding sand, melting of the metal, pouring, forming and...
FOUNDRY, BUILDING-UP TRAINING SET 1 - MCLA
  • MCLA
Available
7.3.3.1.- 주조
MCLA

Foundry, Building-up Training Set 1

Didactic case for the study of foundry fundamentals.Operations of ramming up of the moulding sand, melting of the metal, pouring, forming and fettling can be performed step by step.Practice of melting, unmelting and foundry with irregular and...
CENTRIFUGAL CASTING, BUILDING-UP TRAINING SET 2 - MCEN
  • MCEN
Available
7.3.3.1.- 주조
MCEN

Centrifugal Casting, Building-up Training Set 2

This unit is designed for production of hollow bodies in a fast rotating die.The unit is mounted on a thick steel sheet and hold by a frame of extruded and anodised aluminium, which provides a great stiffness and resistance.This unit is made up of...