MDB Unit Kelendutan Batang Melengkung

7.1.6.- MEKANIKA STRUKTURAL 7.3.2.1.- UJI MEKANIK 14.1.6.- MEKANIKA STRUKTURAL

SISTEM INOVATIF

The Deflection of Curved Bars Unit, "MDB", is designed to enable the student to determine experimentally the horizontal and vertical displacements at the free end of various curved bars when subject to single concentrated load.

Lihat uraian umum

Katalog

Spesifikasi Kontes

Ekspansi

ICAI

Interactive Computer Aided Instruction Software

MSAC

Modular System for Acquisition and Control

Laboratorium

7TV

Laboratorium Mekanika, Otomotif dan Material untuk Pendidikan Teknik dan Vokasi

7HE

Laboratorium Mekanika, Otomotif dan Material Pendidikan Tinggi

BERITA TERKAIT

GAMBARAN UMUM

The Deflection of Curved Bars Unit "MDB" consists of a structure of aluminum and steel that allows the incorporation of different curved bars to be studied. It allows tests with curved bars of different shape.

The use of two dial gauges placed perpendicularly to each other makes it possible to determine the displacements produced in both directions, up to a maximum range of 10 mm.

The load is applied when hanging a set of weights in the application point. A set of weights in supplied with the unit.

LATIHAN DAN PRAKTEK PEDOMAN

LATIHAN PRAKTIS YANG DIANDAL TERMASUK DALAM PANDUAN

Study of deflection of curved bars.
Determination of the horizontal and vertical displacements at the free end of various curved bars when subject to single concentrated loads.
Study of the different types of bars geometry and for different positions.
Measurement of the horizontal and vertical displacements produced at the free end of the curved bar.
Effect of the load value in the bar response.
Effect of the bar morphological characteristics in its response to the load.

PERALATAN KOMPLEMENTER

UNIVERSAL MATERIAL TESTING UNIT - EEU/20KN

EEU/20KN

Available

7.3.2.1.- UJI MEKANIK

EEU/20KN

Unit Tes Material Universal

The Universal Material Testing Unit, "EEU/20KN", is a didactic bench-top universal material testing unit. It is distinguished by its rigid construction, accurate control and a precise hydraulic system to apply loads of up to 20 kN, which enables...

EEDB

Available

7.3.2.1.- UJI MEKANIK

EEDB

Unit Tes Brinell Hardness

The Brinell Hardness Testing Unit, "EEDB", is a hardness tester that determines Brinell hardness in metals, hard alloys, tempered steels, etc. Besides, it can be used with other materials, such as rigid plastics, bakelite, etc.A penetrating ball...

BRINELL, VICKERS & ROCKWELL HARDNESS TESTING UNIT - EBVR

EBVR

Available

7.3.2.1.- UJI MEKANIK

EBVR

Unit Tes Brinell, Vickers dan Rockwell Hardness

The Brinell, Vickers and Rockwell Hardness Testing Unit, "EBVR", consists of a hardness testing machine that determines the three main types of hardness (Brinell, Vickers and Rockwell). It can be adapted to determine hardness of ferrous materials...

EEFCR

Available

7.3.2.1.- UJI MEKANIK

EEFCR

Unit Tes Creep

The Creep Testing Unit, "EEFCR", for the creep testing is mounted on a structure of aluminum profiles which a painted steel panel is supported on.The "EEFCR" unit is designed to carry out experiments on specimens of plastic materials. Due to the...

COMPUTER CONTROLLED FATIGUE TESTING UNIT - EEFC

EEFC

Available

7.3.2.1.- UJI MEKANIK

EEFC

Unit Komputer Kontrol Tes Kelelahan

The Computer Controlled Fatigue Testing Unit, "EEFC", designed by EDIBON, allows to study the fatigue strength of the materials. For that purpose, fatigue tests are performed with different materials and notches.Optionally, with the additional...

Available

7.3.2.1.- UJI MEKANIK

EEF

Unit Tes Kelelahan

The Fatigue Testing Unit, "EEF", designed by EDIBON, allows to study the fatigue strength of the materials. For that purpose, fatigue tests are performed with different materials and notches.Optionally, with the additional recommended element Set...

CHARPY AND IZOD IMPACT TESTING UNIT - EEICI

EEICI

Available

7.3.2.1.- UJI MEKANIK

EEICI

Unit Tes Impact "Charpy dan Izod"

The Charpy and Izod Impact Testing Unit, "EEICI", consists of a pendulum supported on bearings with an arm of 330 mm long and a fastening system in the initial position of the test. The suitable hammer either for Charpy or Izod test is screwed to...

Available

7.3.2.1.- UJI MEKANIK

MUP

Universal Buckling Unit

The Universal Buckling Unit "MUP" is a bench-top unit whose frame is made of anodized aluminum profiles and plates and steel elements, on which a bubble level is installed to equilibrate the system.The unit has been designed to carry out tests...

MFLT

Available

7.3.2.1.- UJI MEKANIK

MFLT

Unit Strut

The Strut Buckling Unit "MFLT" allows the student to obtain experimentally the buckling critical load of slender struts subjected to compression.The unit allows to study the buckling of pieces of different lengths, ranging from 300 mm. to 625 mm.,...

MEBM

Available

7.3.2.1.- UJI MEKANIK

MEBM

Euler Buckling Modes Unit

With the Euler Buckling Modes Unit, "MEBM", the four Euler buckling cases are demonstrated, for which four elastic bars are fixed or supported in a frame and subjected to compression load with a system of weights.The elastic bars can be free or...

Available

7.3.2.1.- UJI MEKANIK

MTP

Unit Putar dan Tekuk

The Torsion and Bend Unit, "MTP", is a combined apparatus for the demonstration of both torsion and bend to be used in the laboratory or as a complement of the theoretical study about torsion and bend. Its size and weight facilitate its transport...

Available

7.3.2.1.- UJI MEKANIK

MTB

Unit Torsi

The Torsion Unit, "MTB", allows to verify the basis of torsion and to perform practical exercises to demonstrate:Circular rods elastic torsion equation.The rigidity modulus of different materials.To perform the tests a metallic rod is fastened by...

KUALITAS

LAYANAN PURNA JUAL

UNTUK INFORMASI LEBIH LANJUT, HUBUNGI KAMI