14.1.- BIOMEKANIKA

Biomekanik mempelajari mekanisme pergerakan makhluk hidup, di antaranya gerakan tubuh manusia. Penelitian ini berkisar dari gerakan yang paling sederhana dalam kehidupan sehari-hari, seperti Kerja atau olah raga, hingga pergerakan beberapa organ dalam, seperti jantung. Untuk mempelajari kinetika tubuh manusia, biomekanik menerapkan prinsip mekanika dan pengetahuan tentang anatomi dan fisiologi, yang memungkinkan rancangan instrumen diagnostik dan perawatan baru serta pengembangan implan dan yang lebih baik prostesis desain.

Lihat Lebih Banyak

Saat ini, Biomekanik menganalisis gerakan kombinasi sendi dan otot. Analisis ini memungkinkan kita untuk mempelajari beban dan upaya yang dilakukan tubuh manusia. Pengetahuan tentang kinetika manusia memungkinkan perawatan cedera dan rehabilitasi selanjutnya, desain prostesis yang memungkinkan fleksibilitas gerakan, pencarian teknik olahraga baru untuk meningkatkan kinerja aktivitas fisik atau pencegahan kerusakan organisme saat melakukan aktivitas di tempat kerja dan di rumah. Pengetahuan ini dapat dibagi menjadi beberapa bidang Biomekanik: Biomekanik Medis, Biomekanik Olahraga dan Biomekanik Kerja. Aplikasi lain dari Biomekanik adalah desain aplikasi robotik. Gerakan yang dilakukan oleh lengan robot atau kapasitas perpindahan beberapa orang melalui sistem lokomotor elektro-mekanis didasarkan pada mekanisme makhluk hidup.

Studi berkelanjutan tentang perilaku mekanis organisme mengarahkan aplikasi biomekanik untuk mengembangkan prostesis bionik dan organisme buatan yang mensimulasikan fungsi normal organisme nyata dan dapat bereaksi terhadap rangsangan. Selain itu, peningkatan teknologi exoskeletons akan meningkatkan mobilitas orang-orang dengan mobilitas terbatas dan meningkatkan kapasitas fisik saat melakukan aktivitas yang berat.

Lihat Produk

BIOMEKANIKA PERALATAN

Menampilkan 73 -96 dari 112 produk

MARP

Available

7.1.6.- MEKANIKA STRUKTURAL

MARP

Peralatan Busur Parabola

The Parabolic Arch Unit "MARP" contains a pre-shaped articulated arch, which can be subjected to point or evenly distributed loads by means of seven uniformly distributed cables (cords) with hangers.One support of the arch is fixed whereas the...

MART

Available

7.1.6.- MEKANIKA STRUKTURAL

MART

Peralatan Busur Tiga Titik Artikulasi

The Three-Hinged Arch Unit "MART" allows the student to become familiar with three-hinged arches, to calculate the bearing forces (for point load, for uniformly distributed load and for moving load), to investigate the influence of the load on the...

UNIT FOR STUDYING FORCES IN A SIMPLE BAR STRUCTURE - MFBS

MFBS

Available

7.1.6.- MEKANIKA STRUKTURAL

MFBS

Peralatan untuk Studi Gaya pada Struktur Batang Sederhana (Rangka Sederhana)

The Unit for Studying Forces in a Simple Bar Structure, "MFBS", designed by EDIBON allows the study of forces acting on a simple truss when is subjected to a point load in one of the nodes that make up the structure.It consists of a group of five...

UNIT FOR STUDYING FORCES IN DIFFERENT SINGLE PLANE TRUSSES - MFCS1

MFCS1

Available

7.1.6.- MEKANIKA STRUKTURAL

MFCS1

Peralatan Studi Gaya pada Berbagai Konfigurasi Rangka Bidang

The Unit for studying Forces in Different Single Plane Trusses, "MFCS1", designed by EDIBON, allows the measurement of the bar forces in various single plane trusses, the study of the dependency on the external force and the comparison of the...

UNIT FOR STUDYING FORCES IN AN OVERDETERMINATE TRUSS - MFCS2

MFCS2

Available

7.1.6.- MEKANIKA STRUKTURAL

MFCS2

Peralatan Studi Gaya pada Rangka Hiperstatik

The Unit for studying Forces in an Overdeterminate Truss, "MFCS2", designed by EDIBON, allows the measurement of the bar forces in a statically determinate truss and in a statically overdeterminate truss, the study of the distribution of forces in...

UNIT FOR STUDYING DEFORMATION OF TRUSSES - MFCS3

MFCS3

Available

7.1.6.- MEKANIKA STRUKTURAL

MFCS3

Peralatan untuk Studi Deformasi pada Rangka

The Unit for studying Deformation of Trusses, "MFCS3", designed by EDIBON, allows the measurement of the stresses in the bars in different types of trusses, and the study of the dependence of the external force and the comparison of the...

Available

7.1.6.- MEKANIKA STRUKTURAL

MFL

Peralatan Busur Dua Titik Artikulasi

The Two Hinged Arch Unit, "MFL", designed by EDIBON allows to study the response of an arched beam when an external load is applied on it.The arch is supported on two supports, a fixed one and a movable one. The displacement and horizontal...

Available

7.1.6.- MEKANIKA STRUKTURAL

MPO

Peralatan Portal

The Portal Frame Unit, "MPO", designed by EDIBON, allows for precise measurements of vertical and horizontal deflection in an embedded rectangular portal frame. By applying various loads with specific weights, changes in the portal frame’s...

Available

7.1.6.- MEKANIKA STRUKTURAL

STH

Peralatan Hipotesis Tegangan

The Stress Hypotheses Unit, "STH", allows the study and testing of stress hypotheses by applying loads in different directions on a test specimen point and measuring the deformations produced.Normal and shear stresses are applied, avoiding...

SIMPLE STABILITY PROBLEMS STUDY UNIT - MEPE

MEPE

Available

7.1.6.- MEKANIKA STRUKTURAL

MEPE

Peralatan untuk Studi Masalah Stabilitas

The Simple Stability Problems Study Unit, "MEPE", has been designed to study the stability of a bar subjected to buckling by obtaining the critical load in different configurations. The unit consists of two bars of same length connected by a...

UNIT FOR STUDYING METHODS TO DETERMINE THE ELASTIC LINE - MDLE

MDLE

Available

7.1.6.- MEKANIKA STRUKTURAL

MDLE

Peralatan Studi Metode untuk Menentukan Garis Elastis

The Unit for studying Methods to Determine the Elastic Line, "MDLE", consists of set of beams, several supports (with clamp fixing and dial gauges, and with force gauge), a device to generate a bending moment, fixed pulleys, dial gauges and a set...

UNIT TO STUDY STRESS ON A MEMBRANE - SSM

Available

7.1.6.- MEKANIKA STRUKTURAL

SSM

Peralatan untuk Studi Tegangan pada Membran

The Unit to Study Stress on a Membrane, "SSM", designed by EDIBON, allows the study of stresses and deformations in a thin disc or membrane subjected to different compressive stresses.The main element of the equipment is a thin disc or membrane...

Available

7.1.6.- MEKANIKA STRUKTURAL

MVV

Peralatan Balok Kantilever

The system consists of a vertical cantilever rigidly clamped at its lower end to the main column which is attached to a rigid structure. Beams of different sections may be used.A loading head, located at the upper end of the column, can rotate...

Available

7.3.2.1.- UJI MEKANIK

MDB

Peralatan Defleksi pada Batang Melengkung

The Deflection of Curved Bars Unit "MDB" consists of a structure of aluminum and steel that allows the incorporation of different curved bars to be studied. It allows tests with curved bars of different shape.The use of two dial gauges placed...

Available

7.3.2.1.- UJI MEKANIK

MFV

Demonstrator Lenturan Balok

The Beam Deflection Unit, "MFV" has been designed to enable the students to observe and study the following phenomena in simply supported beams and cantilever beams:Relation between the deflections and the applied loads.Effect of the length and...

MFLT

Available

7.3.2.1.- UJI MEKANIK

MFLT

Peralatan Tekuk pada Batang

The Strut Buckling Unit "MFLT" allows the student to obtain experimentally the buckling critical load of slender struts subjected to compression.The unit allows to study the buckling of pieces of different lengths, ranging from 300 mm. to 625 mm.,...

EEICI/300

Available

7.3.2.1.- UJI MEKANIK

EEICI/300

Peralatan Uji Dampak Charpy dan Izod 300Nm

The 300 Nm Charpy and Izod Impact Testing Unit, "EEICI/300", designed by EDIBON, consists of a pendulum supported by bearings with a 900 mm long arm and a clamping system at the starting position of the test. At one end of the pendulum, either the...

Available

7.3.2.1.- UJI MEKANIK

MUP

Peralatan Universal untuk Tekuk

The Universal Buckling Unit "MUP" is a bench-top unit whose frame is made of anodized aluminum profiles and plates and steel elements, on which a bubble level is installed to equilibrate the system.The unit has been designed to carry out tests...

SHEAR FORCE AND BENDING MOMENTUM UNIT - MMF

Available

7.3.2.1.- UJI MEKANIK

MMF

Peralatan Momen Lentur dan Gaya Geser

The Shear Force and Bending Momentum Unit, "MMF", designed by EDIBON, is formed by an aluminum and steel structure that allows us to perform a mechanical study of different structures.An articulated structure makes it possible to convert the...

COMPUTER CONTROLLED PHOTOELASTICITY UNIT - EFOC

EFOC

Available

7.3.1.- FOTOELASTISITAS DAN PENGUKURAN STRAIN

EFOC

Peralatan Fotoelastisitas, Dikendalikan dari Komputer (PC)

Unit for photoelasticity practices, illustrating the subjects of the photoelasticity theory, the elasticity theory, strength of materials, and structure theory.It is very suitable for the introduction and study of photoelasticity: optical...

Available

7.3.1.- FOTOELASTISITAS DAN PENGUKURAN STRAIN

EFO

Peralatan Fotoelastisitas

Unit for photoelasticity practices, illustrating the subjects of the Photoelasticity theory, the Elasticity theory, Strength of Materials, and Structure theory.It is very suitable for the introduction and study of photoelasticity: optical...

COMPUTER CONTROLLED PHOTOELASTICITY UNIT WITH ARTIFICIAL VISION SYSTEM - EFOV

EFOV

Available

7.3.1.- FOTOELASTISITAS DAN PENGUKURAN STRAIN

EFOV

Peralatan Fotoelastisitas dengan Sistem Penglihatan Buatan, Dikendalikan dari Komputer (PC)

UNIT FOR DETERMINING THE GAUGE FACTOR OF STRAIN GAUGES - MFGE

MFGE

Available

7.3.1.- FOTOELASTISITAS DAN PENGUKURAN STRAIN

MFGE

Peralatan untuk Penentuan Faktor Strain Gauge

The Unit for Determining the Gauge Factor of Strain Gauges, "MFGE", designed by EDIBON, allows to determine the k factor of strain gauges.The bar rests on two supports with ball bearings, so that it is possible to work with a load under pure...

MEGE

Available

7.3.1.- FOTOELASTISITAS DAN PENGUKURAN STRAIN

MEGE

Peralatan Pelatihan Strain Gauge

The Strain Gauge Training Unit, "MEGE", provides an introduction to the fundamentals of measurement with strain gauges, to compare how resistance strain gauges work and how they measure strains in different structures (torsion, tension and bending...

UNTUK INFORMASI LEBIH LANJUT, HUBUNGI KAMI