7.3.- TEKNIK MATERIAL

Teknik material adalah cabang ilmiah dan industri yang bertanggung jawab untuk membuat interpretasi industri dari ilmu material. Secara antropologis, berbagai tahapan manusia pengembangan telah diklasifikasikan menurut bahan yang digunakan dalam pembuatan alat (Zaman Batu, Zaman Perunggu, dll.). Dengan demikian, perkembangan umat manusia terkait erat dengan studi tentang bahan baru.

Lihat Lebih Banyak

Selama 200 tahun terakhir, penemuan tentang material, yang mengungkapkan kontribusi dari Gibbs, telah dibuat. Dia mendemonstrasikan adanya hubungan antara properti material dan strukturnya. Penemuan ini telah memungkinkan pengembangan materi baru, seperti graphene, dan penyelidikan bidang baru, seperti nanomaterial atau nanoteknologi.

Sejumlah besar pengujian telah dilakukan untuk mencapai tingkat pengembangan tersebut, termasuk pengujian tekukan mekanis, pengujian kekerasan (Rockell, Brinell, Vickers, Martens), uji torsi, uji tarik (ketangguhan dan ketahanan), uji tarik (creep ), pengujian geser, serta uji kimia (perlakuan termal, struktur internal, dll.). Demikian pula, bahan dapat diklasifikasikan sebagai:

  • Logam (ferrous dan non-ferrous).
  • Keramika.
  • Polimer (termoplastik, plastik termoseting, dan elastomer).
  • Bahan komposit.

Penerapan kemajuan ini terbukti di berbagai area industri, seperti otomotif, elektronik, dirgantara, aeronautika dan biomedis, sehingga memberikan teknik material pentingnya hal tersebut dalam masyarakat saat ini.

Lihat Produk
Materi Terkait

TEKNIK MATERIAL PERALATAN

1.- FISIKA 2.- ELEKTRONIKA 3.- KOMUNIKASI 4.- LISTRIK 5.- ENERGI 6.- MEKATRONIK & OTOMASI 7.- MEKANIKA 8.- MEKANIKA FLUIDA 9.- TERMODINAMIK DAN TERMOTEKNIK 10.- PENGENDALIAN PROSES 11.- TEKNIK KIMIA 12.- TEKNOLOGI PANGAN & AIR 13.- LINGKUNGAN HIDUP 14.- TEKNIK BIOMEDIS AKSESORIS LABORATORIUM PABRIK PILOT SESUAI PESANAN
7.1.- TEKNIK MESIN 7.2.- TEKNIK MEKANIK OTOMOTIF 7.3.- TEKNIK MATERIAL 7.4.- PEMASANGAN DAN PEMELIHARAAN
7.3.1.- FOTOELASTISITAS DAN PENGUKURAN STRAIN 7.3.2.- PENGUJIAN MATERI 7.3.3.- TEKNIK MANUFAKTUR DAN PEMELIHARAAN
7.3.2.1.- UJI MEKANIK 7.3.2.2.- UJI TERMAL DAN AKUSTIK 7.3.3.1.- PENDANAAN
Menampilkan 13 -24 dari 30 produk
12 24 36
CHARPY AND IZOD IMPACT TESTING UNIT - EEICI
  • EEICI
Available
7.3.2.1.- UJI MEKANIK

EEICI

Peralatan Uji Dampak Charpy dan Izod

The Charpy and Izod Impact Testing Unit, "EEICI", consists of a pendulum supported on bearings with an arm of 330 mm long and a fastening system in the initial position of the test. The suitable hammer either for Charpy or Izod test is screwed to...
Lihat Unit
  • EEICI/300
Available
7.3.2.1.- UJI MEKANIK

EEICI/300

Peralatan Uji Dampak Charpy dan Izod 300Nm

The 300 Nm Charpy and Izod Impact Testing Unit, "EEICI/300", designed by EDIBON, consists of a pendulum supported by bearings with a 900 mm long arm and a clamping system at the starting position of the test. At one end of the pendulum, either the...
Lihat Unit
UNIVERSAL BUCKLING UNIT - MUP
  • MUP
Available
7.3.2.1.- UJI MEKANIK

MUP

Peralatan Universal untuk Tekuk

The Universal Buckling Unit "MUP" is a bench-top unit whose frame is made of anodized aluminum profiles and plates and steel elements, on which a bubble level is installed to equilibrate the system.The unit has been designed to carry out tests...
Lihat Unit
STRUT BUCKLING UNIT - MFLT
  • MFLT
Available
7.3.2.1.- UJI MEKANIK

MFLT

Peralatan Tekuk pada Batang

The Strut Buckling Unit "MFLT" allows the student to obtain experimentally the buckling critical load of slender struts subjected to compression.The unit allows to study the buckling of pieces of different lengths, ranging from 300 mm. to 625 mm.,...
Lihat Unit
EULER BUCKLING MODES UNIT - MEBM
  • MEBM
Available
7.3.2.1.- UJI MEKANIK

MEBM

Peralatan Modus Tekuk Euler

With the Euler Buckling Modes Unit, "MEBM", the four Euler buckling cases are demonstrated, for which four elastic bars are fixed or supported in a frame and subjected to compression load with a system of weights.The elastic bars can be free or...
Lihat Unit
TORSION AND BEND UNIT - MTP
  • MTP
Available
7.3.2.1.- UJI MEKANIK

MTP

Peralatan Torsi dan Lentur

The Torsion and Bend Unit, "MTP", designed by EDIBON, is a combined unit for the demonstration of both torsion and bend to be used in the laboratory or as a complement of the theoretical study about torsion and bend. Its size and weight facilitate...
Lihat Unit
TORSION UNIT - MTB
  • MTB
Available
7.3.2.1.- UJI MEKANIK

MTB

Peralatan Torsi

The Torsion Unit, "MTB", has been designed by EDIBON to verify the basis of torsion and to perform practical exercises to demonstrate:Circular rods elastic torsion equation.The rigidity modulus of different materials.To perform the tests a...
Lihat Unit
TORSION TEST UNIT (30NM) - MTT
  • MTT
Available
7.3.2.1.- UJI MEKANIK

MTT

Peralatan Uji Torsi (30Nm)

To perform the tests, the test specimen is clamped and twisted by means of a flywheel and a worm gear until it breaks. The force is gradually applied to the specimen to observe the elastic strain produced. The specimen will deform and manifest...
Lihat Unit
TENSILE TESTER UNIT - MTTU
  • MTTU
Available
7.3.2.1.- UJI MEKANIK

MTTU

Peralatan Uji Tarik

With the Tensile Tester Unit, "MTTU", designed by EDIBON, tensile test can be performed. A specimen made of different materials is subjected to an increasing axial tensile stress till failure. This unit allows the user to perform tensile tests...
Lihat Unit
DEFLECTION OF CURVED BARS UNIT - MDB
  • MDB
Available
7.3.2.1.- UJI MEKANIK

MDB

Peralatan Defleksi pada Batang Melengkung

The Deflection of Curved Bars Unit, "MDB", designed by EDIBON, consists of a structure of aluminum and steel that allows the incorporation of different curved bars to be studied. It allows tests with curved bars of different shape.The use of two...
Lihat Unit
BEAM DEFLECTION UNIT - MFV
  • MFV
Available
7.3.2.1.- UJI MEKANIK

MFV

Demonstrator Lenturan Balok

Computer Controlled Modular Hydraulic Turbine Unit, "HTMC", has been designed by EDIBON for the study and comparison of different types of small scale hydraulic turbines, allowing the determine the operation characteristics of this type of...
Lihat Unit
SHEAR FORCE AND BENDING MOMENTUM UNIT - MMF
  • MMF
Available
7.3.2.1.- UJI MEKANIK

MMF

Peralatan Momen Lentur dan Gaya Geser

The Shear Force and Bending Momentum Unit, "MMF", designed by EDIBON, is formed by an aluminum and steel structure that allows us to perform a mechanical study of different structures.An articulated structure makes it possible to convert the...
Lihat Unit
Meminta informasi