MRYE1 Wheel and Axle Unit

7.1.3.- STATICS AND DYNAMICS 14.1.3.- STATICS AND DYNAMICS

SISTEM INOVATIF

The Wheel and Axle Unit, "MRYE1", is a unit which allows to investigate the mechanics of a simple wheel and axle machine and to demonstrate the laws of the formation of equilibrium of moments in static systems.

Lihat uraian umum

Katalog

Spesifikasi Kontes

Ekspansi

ICAI

Interactive Computer Aided Instruction Software

MSAC

Modular System for Acquisition and Control

Laboratorium

7TV

Laboratorium Mekanika, Otomotif dan Material untuk Pendidikan Teknik dan Vokasi

7HE

Laboratorium Mekanika, Otomotif dan Material Pendidikan Tinggi

BERITA TERKAIT

GAMBARAN UMUM

Two pulleys with different diameter have an axle supported on pivots with ball bearings in a base plate. Each pulley (wheel) has a cord wrapped around its periphery. The cords can be wrapped in either direction around each pulley.

A weights holder is added to each cord, allowing the loading of the pulleys using the set of weights provided. These weights can be easily changed, thus allowing to quickly vary the peripheral force on the pulleys.

Using the holders and weights the velocity ratio can be experimentally determined and compared with the calculated values. Students can also determine the variation of effort with load and the variation of efficiency with load.

LATIHAN DAN PRAKTEK PEDOMAN

LATIHAN PRAKTIS YANG DIANDAL TERMASUK DALAM PANDUAN

Study of equilibrium of moments.
Determination of velocity ratio and comparison with calculated value.
Determination of variation of effort with load.
Determination of variation of efficiency with load.

PERALATAN SIMILAR TERSEDIA

WHEEL AND DIFFERENTIAL AXLE UNIT - MRYE2

MRYE2

Available

7.1.3.- STATICS AND DYNAMICS

MRYE2

Wheel and Differential Axle Unit

The Wheel and Differential Axle Unit, "MRYE2", is a unit that allows for investigating the mechanics of a wheel and differential axle mechanism and demonstrating the force reduction on a differential pulley block.A wheel, consisting of a pulley...

PERALATAN KOMPLEMENTER

UNIT FOR STUDYING EQUILIBRIUM OF MOMENTS ON A TWO ARM LEVER - MEMB2

MEMB2

Available

7.1.3.- STATICS AND DYNAMICS

MEMB2

Unit for studying Equilibrium of Moments on a Two Arm Lever

The Unit for studying Equilibrium of Moments on a Two Arm Lever,"MEMB2", allows to study the fundamentals of the equilibrium of moments and the application of the law of levers on a two-arm lever.A pivoted beam in the extreme of a vertical support...

COMPUTER CONTROLLED BALANCE OF RECIPROCATING MASSES UNIT - MBMRC

MBMRC

Available

7.1.3.- STATICS AND DYNAMICS

MBMRC

Computer Controlled Balance of Reciprocating Masses Unit

The Computer Controlled Balance of Reciprocating Masses Unit "MBMRC" is a bench-mounting unit that allows to investigate and examine the free masses and moments of a reciprocating engine with a single cylinder, with two cylinders or with four...

MEAL

Available

7.1.3.- STATICS AND DYNAMICS

MEAL

Cam Analysis Unit

The Cam Analysis Unit "MEAL" allows to observe the effect of the profile of a cam, the study of the displacement, velocity and acceleration profiles of the cam and the identification of the factors that can modify the dynamics of the cam. This...

CORIOLIS FORCE DEMONSTRATION UNIT - MDFC

MDFC

Available

7.1.3.- STATICS AND DYNAMICS

MDFC

Coriolis Force Demonstration Unit

The Coriolis Force Demonstration Unit, "MDFC", is used to observe the deflection of a jet of water generated by a pump attached to a rotating arm that rotates to different speeds in a horizontal plane. An electronically controlled motor rotates...

MFCE

Available

7.1.3.- STATICS AND DYNAMICS

MFCE

Centrifugal Force Unit

The Centrifugal Force Unit, "MFCE", is used to demonstrate the relationship between centrifugal force, rotational speed, mass of a rotating body and distance from the axis. The unit consists of a vertical axis of rotation and a rotating arm....

Available

7.1.3.- STATICS AND DYNAMICS

MGI

Gyroscope

The Gyroscope, "MGI", allows the experimental demonstration of the different rotation modes of a gyroscope and the moments generated by the gyroscopic effect. The rotor of the electric motor (rotating motor) shares a horizontally supported shaft...

Available

7.1.3.- STATICS AND DYNAMICS

CGU

Centrifugal governor unit

The Centrifugal Governor Unit, "CGU", has been designed to study the operating mode of different centrifugal governors, including three interchangeable governors: Porter governor, Hartnell governor and Proell governor.Interchangeable governors...

Available

7.1.3.- STATICS AND DYNAMICS

MED

Static and Dynamic Balancing Unit

The Static and Dynamic Balancing Unit, "MED", developed by EDIBON is a unit to study and analyze the oscillations and vibrations and how to eliminate or diminish them.Basically, the unit is formed by a shaft mounted on bearings. The shaft is...

Available

7.1.3.- STATICS AND DYNAMICS

MES

Simple Balancing Unit

The Simple Balancing Unit "MES" developed by EDIBON is an unit to study and analyze the oscillations and vibrations and how to eliminate or diminish them.This unit is sustained by anodized aluminum profiles on which are mounted steel panels. This...

Available

7.1.3.- STATICS AND DYNAMICS

MIF

Inertia Flywheel Unit

The Inertia Flywheel Unit, "MIF", consists of an inertia disc with a rotation shaft at the center of the disc.The shaft is supported at two points by bearings.A cord is attached by one of the ends to the shaft and wound around it. At the other end...

MRYE2

Available

7.1.3.- STATICS AND DYNAMICS

MRYE2

Wheel and Differential Axle Unit

MELH

Available

7.1.3.- STATICS AND DYNAMICS

MELH

Unit for studying Hooke's Law

The Unit for studying Hooke's Law, "MELH", demonstrates the application of Hooke's Law and allows the visualization of the deformation of tension springs under load and the performance of oscillation experiments on a spring – mass system.The...

KUALITAS

LAYANAN PURNA JUAL

UNTUK INFORMASI LEBIH LANJUT, HUBUNGI KAMI