MCF Belt Friction Unit

7.1.5.- TRIBOLOGY (FRICTION, WEAR, LUBRICATION) 14.1.5.- TRIBOLOGY (FRICTION, WEAR, LUBRICATION)

SISTEM INOVATIF

The Belt Friction Unit, "MCF", allows us to carry out studies and investigations to compare the driving torque for a given degree of overlap of a flat belt (leather or rope) and a V belt.

Lihat uraian umum

Katalog

Spesifikasi Kontes

Ekspansi

ICAI

Interactive Computer Aided Instruction Software

MSAC

Modular System for Acquisition and Control

Laboratorium

7TV

Laboratorium Mekanika, Otomotif dan Material untuk Pendidikan Teknik dan Vokasi

7HE

Laboratorium Mekanika, Otomotif dan Material Pendidikan Tinggi

BERITA TERKAIT

GAMBARAN UMUM

The Belt Friction Unit, "MCF", allows us to carry out studies and investigations to compare the driving torque for a given degree of overlap of a flat belt (leather or rope) and a V belt.

With this unit the relationship between the tensions in the two sides of a belt can be observed, to evaluate the differences between flat (leather or rope) and V belts and to investigate the effect of the angle lap, among others.

Tension is introduced into the belt by hanging masses or weights. The slipping torque is determined by the addition of suitable masses attached to a cord wrapped round the drum.

LATIHAN DAN PRAKTEK PEDOMAN

LATIHAN PRAKTIS YANG DIANDAL TERMASUK DALAM PANDUAN

Investigation of the relationship between the belt tensions and the angle of lap for a flat belt.
Comparison of the driving torque for a given angle of lap.

LEBIH BANYAK LATIHAN PRAKTIS YANG AKAN DILAKUKAN DENGAN UNIT

Evaluation of the differences between flat belts and V-shaped belts.
Evaluation of the differences between V-shaped toothed and flat belts.
Determination of the coefficient of friction between the pulley and belt for the belt sections.
Verification of the belt tension equation.

PERALATAN SIMILAR TERSEDIA

BELT FRICTION UNIT WITH DYNAMOMETERS - MCF/A

MCF/A

Available

7.1.5.- TRIBOLOGY (FRICTION, WEAR, LUBRICATION)

MCF/A

Belt Friction Unit with Dynamometers

The Belt Friction Unit with Dynamometers, "MCF/A", allows studies and investigations to compare the friction coefficient for a given contact angle of a flat belt and a V-belt.With this unit it is possible to observe the relationship between...

PERALATAN KOMPLEMENTER

Available

7.1.5.- TRIBOLOGY (FRICTION, WEAR, LUBRICATION)

MEF

Friction Study Unit

The Friction Study Unit, "MEF", allows the unit to illustrate the friction force by simple demonstrations.It is designed for the study of the relations between friction forces and normal forces, between hard or soft surfaces, between lubricated or...

MPCO

Available

7.1.5.- TRIBOLOGY (FRICTION, WEAR, LUBRICATION)

MPCO

Journal Bearing Unit

The Journal Bearing Unit, "MPCO", allows to study the pressure distribution in sliding bearings. It illustrates the principle of hydrodynamic lubrication.The unit is mounted on a metallic structure assembled on wheels for its mobility.The sliding...

MEMT

Available

7.1.5.- TRIBOLOGY (FRICTION, WEAR, LUBRICATION)

MEMT

Tribology Modular Unit

The Tribology Modular Unit, "MEMT", consists of a base unit with electronic console and a series of experimental units to investigate and visualize tribological phenomena.MEMT-UB. Drive Unit for Tribological Tests. This unit is common for the...

DRIVE UNIT FOR TRIBOLOGICAL TESTS - MEMT-UB

MEMT-UB

Available

7.1.5.- TRIBOLOGY (FRICTION, WEAR, LUBRICATION)

MEMT-UB

Drive Unit for Tribological Tests

This unit is common for the modules type "MEMT". It consists of a base unit and an electronic console:The Base Unit consists of a drive unit formed by a DC motor with a shaft. The motor is mounted in a reduction gear, obtaining enough torque in...

RADIAL PRESSURE DISTRIBUTION IN A JOURNAL BEARING - MEMT-1

MEMT-1

Available

7.1.5.- TRIBOLOGY (FRICTION, WEAR, LUBRICATION)

MEMT-1

Radial Pressure Distribution in a Journal Bearing

This unit allows the visualization of the radial pressure distribution in a journal bearing with hydrodynamic lubrication.The "MEMT-1" unit consists of a journal bearing with hydrodynamic lubrication, a freely moving bearing housing with thirteen...

DYNAMIC FRICTION OF A CYLINDER ON A ROLLER - MEMT-2

MEMT-2

Available

7.1.5.- TRIBOLOGY (FRICTION, WEAR, LUBRICATION)

MEMT-2

Dynamic Friction of a Cylinder on a Roller

This unit allows to demonstrate the friction forces between several cylinders of different materials and a roller under different lubrication conditions.The "MEMT-2" unit consists of two levers that transmit a force applied by weights to a test...

DYNAMIC FRICTION OF A PIN ON A DISC - MEMT-3

MEMT-3

Available

7.1.5.- TRIBOLOGY (FRICTION, WEAR, LUBRICATION)

MEMT-3

Dynamic Friction of a Pin on a Disc

This unit allows to study the friction forces between several vertical friction pins of different materials and a rotating friction disc.The end of each vertical pin is made of a different material and rubs against the rotating steel disc. The...

MEMT-4

Available

7.1.5.- TRIBOLOGY (FRICTION, WEAR, LUBRICATION)

MEMT-4

Rolling Friction in Wheels

This module allows to determine the slip forces between two rotating friction discs in contact.The slip between the discs is maintained constant by a gearbox. The pressure can be adjusted with a lever and a set of weights. The unit includes a...

MEMT-5

Available

7.1.5.- TRIBOLOGY (FRICTION, WEAR, LUBRICATION)

MEMT-5

Elastohydrodynamic Lubrication

This unit allows to investigate the thickness and characteristics of a lubricant film on a rolling sphere.The unit consists in a steel sphere and a driven glass disc.The sphere is pressed against the underside of the glass disc. The light from a...

MEMT-6

Available

7.1.5.- TRIBOLOGY (FRICTION, WEAR, LUBRICATION)

MEMT-6

Friction Vibration

This module allows to demonstrate the static friction, the sliding friction, the related friction vibrations and the slip-stick effects.Several weights are placed on a horizontally rotating friction disc. It is prevented from turning by a cord....

Available

7.1.5.- TRIBOLOGY (FRICTION, WEAR, LUBRICATION)

MCD

Thin Cylinder Unit

The Thin Cylinder Unit, "MCD", has been developed to enable the student to verify various analytical formulae with actual measured results. Strain gauges mounted in various positions and orientations on the cylinder provide an opportunity for...

UNIT FOR STUDYING BEARING FRICTION - MBF

Available

7.1.5.- TRIBOLOGY (FRICTION, WEAR, LUBRICATION)

MBF

Unit for Studying Bearing Friction

The Unit for Studying Bearing Friction, "MBF", has been designed by EDIBON to study sliding friction in slide bearings and rolling bearings. Since rolling friction is very little, rotational dynamics basic tests can be performed with the inertia...

KUALITAS

LAYANAN PURNA JUAL

UNTUK INFORMASI LEBIH LANJUT, HUBUNGI KAMI